0
Add your answer:
Earn +20 pts
Which is larger in inches 7mm or 1cm?
1cm = 10mm Therefore 1cm is larger than 7mm
Is 1 inch larger than 10mm?
There are 25.4 mm in 1 inch. Therefore an inch is larger than 10 mm.
Is a meter smaller or larger than a millimeter?
a meter is larger than a milimeter. There are 10mm in 1cm and 100 cm in 1 meter. So there are 1000 milimeters in a meter
How big is 13mm in size?
A tiny amount more than half an inch.
What is the surgace area of a cylindrical ring or torus if its outside diameter is 16mm andits inside diameter is 10mm?
To find the surface area of a cylindrical ring or torus, you can use the formula A = 2πrh, where r is the average radius of the ring and h is the height or thickness of the ring. In this case, the average radius is (16mm + 10mm)/2 = 13mm and h can be any desired value. Therefore, the surface area of the cylindrical ring or torus is 2π(13mm)(h).
How wide is a German cockroach?
There are about 4000 sub-species of cockroach, some larger than others. Domestic cockroaches in Germany are fairly ordinary and can be about 10mm in width.The species Blattella Germanica, or the German cockroach is considerably smaller measuring about 13mm in length and less than a quarter of this in width.
Is the 5.56 NATO larger than the 10 mm auto?
Well, the 10mm bullet is WIDER than the 5.56mm, but the 5.56 round is longer than a 10mm round.
How many centimeters is 12x12x13 mm?
1cm has 10mm therefor 1mm = 0.1cmAnd 12*12*13mm= 1872mm which is = 187.2 cm
How do you change a thermostat on 2000 BMW?
you will need a 32mm wrench a 10mm 11mm 13mm socket and a flat head screw driver. With the 32mm wrench, take the fan blade off by turning clock wise. Once fan is out of the way use the screw driver to remove the clips on the upper & lower rad. hoes. the thermostat is held on with 3 10mm bolts take them off and 1 13mm bolt. when you remove the 13mm bolt you will also need to loosing the 11mm nut that holds the engine pull bracket. install in rev. order
Which of these is the larger round 5.56 NATO 9mm luger 10mm auto 416berrett?
416
How can you replace the tension pulley on a 1997 Nissan Maxima?
Loosen 13mm nut that secures tension pulley. Then loosen 13mm nut/bolt just above tensioner assembly facing upwards, to remove tension from belt. Then finally remove the three 10mm bolts holding tensioner assembly to engine block. Install in reverse order.
How do you replace a drivers wing panel on 1999 corsa?
there are 7 bolts (5) 13mm and (2) 10mm (3) on the top under the bonet (1) inside as you open the door at the top near the hinge (1) inside behind the mud flap and the (2) 10mm bolts just behind wheel arch at the top
How do you remove astra mk3 roof rails?
First undo the plastic trim around the headlining, drop the headlining and then undo the 10mm or 13mm nuts. You do not need to take out the full headlining, just drop it in that area.
How do you replace the alternator on a 1996 Chevy Corsica 6 cylinder?
disconnect battery remove vent hose remove belt on top u will see 2 black metal brackets which connect to upper intake both are 13mm remove those the remove 13mm bolt from back of alt you will need to uplug sensor to alt to do this then remove 13mm bolt from front of alt then youll need 15mm open end wrench and 13mm socket to remove other bolt located on left side of alt then remove 10mm bolt which holds red wire to install reverse steps
If you have a half inch threaded bolt and trying to thread into a mm hole it almost fits but stops after a couple turns what size mm bolt do you need?
12mm is a little smaller and 13mm is a little larger than a 1/2 inch bolt.
How do you replace water outlet on an Oldsmobile alero 2000?
Just unbolt the power steering pump (2 -13mm bolts) and its right there, 2 10mm bolts and the outlet coms out. New one goes in with gasket and silicone and your good to go...
How do you replace the air compressor on a 1989 Chevy Cavalier Z24 with a 2.8L engine?
There are three 13mm bolts on the front of the compressor and one 10mm bolt on the back. the rest is recovering the froen, taking the lines off, there is a plug on the back of the compressor.
