answersLogoWhite

0

What else can I help you with?

Continue Learning about Math & Arithmetic

What is a real life example on circles?

finding the measurement of a port hole on a ship


How much rock needed to fill a 3 foot by two foot hole?

(3 x 2 x depth of the hole in feet) cubic feet


What is a synonym for-abyss?

Chasm, crevasse, void, deep hole, or depth. Those words mean abyss.


How much concrete do you need to fill a hole 6 inches by 42 inches?

None, as a hole which is 6 inches wide and 42 inches long has no depth and thus no volume.


How do you calculate percolation rate?

Percolation rate describes how long it takes for standing water in a hole to move through the bottom and the walls of that hole.Basically, a hole with known dimensions is made, usually with a soil auger, post hole digger or shovel, and then a volume of water is added to the hole. The depth to the water surface is then measured. The surface of the water in the hole will drop as the water seeps into the soil. The depth to the water surface is measured repeatedly at set intervals (let's say these intervals are 10 minutes apart, for the sake of this question). Then, after each measurement, more water is added to the hole to fill it up to that original level, again.Normally, when water is first added to the hole, the water will move through the soil fairly quickly. As the soil become saturated (all pores fill with water), the rate of water loss in the hole will slow down. When it reaches a steady rate of loss, that rate is taken as the percolation rate.For example: After repeatedly measuring water levels, you find that the water level drops 3 cm every ten minutes. The percolation rate for that hole would be:10min/3cm = 3.33 cm/min.This percolation rate can only be realistically compared to percolation tests run with the same size hole, with the same depth of water.Percolation tests for percolation rates are quick and dirty ways to estimate the soil's saturated hydraulic conductivity(Ksat). They are of limited value in comparison to actually running a Ksat measurement, which is directly comparable to other Ksat measurements, regardless of the size of the hole, how much water was put into it, and (hopefully) the scientist or technician running the test.Some US states still use "perc tests" to determine the size and design of septic systems that they will allow a landowner to build on his/her property. One method, apparently used in Minnesota, can be found at the link.

Related Questions

Marcel is digging a hole using a shovel He knows that the final depth in feet of the hole will be a function of the number of minutes spent digging Zack names this function Depthminutes and he?

The correct answer is: D(45) is the depth, in feet, of the hole after digging for 45 minutes.


How do you use a steel rule?

Its principal feature is the start datum or 0 is the end of the ruler, typical use would be measuring the depth of a feature, such as a blind bored hole.


What is the depth of the deepest hole on Earth?

The depth of the deepest hole on Earth is about 7.5 miles (12 kilometers).


What actors and actresses appeared in Blind Hole - 2012?

The cast of Blind Hole - 2012 includes: Drew Altman


What is depth of orifice?

An "orifice" is a word for a hole (usually a hole in an animal's body". Therefore the "depth of an orifice" would be a measure of the length from the hole opening to the closed end.


What is the spelling of deep in spanish?

Depends upon what "deep" signifies to you. Also, whose Spanish you are speaking (Spain, Latin America, Puerto Rico, etc) fondo -- as the measurement of a hole--depth hondo deep, low; profound hondura depth, profundity MH Dolan


Measurement of a golf hole cup in professional golf?

The measurement of a golf hole for a golf course is always 4 1/4 inches.


What is the measurement in a golf hole?

The actual hole? 4 1/4 inches or a golf hole? About 100-600 yards.


Can you give me a sentence with the word unfathomable?

The depth of the hole was unfathomable.


What is the standard depth for a dowel hole in woodworking projects?

The standard depth for a dowel hole in woodworking projects is typically around 1 to 1.5 times the diameter of the dowel being used.


How can I drill a pocket hole without using a jig?

To drill a pocket hole without using a jig, you can use a regular drill and a pocket hole drill bit. First, set the drill bit to the correct depth for the thickness of your wood. Then, angle the drill bit at 15 degrees and drill into the wood at the desired location for the pocket hole. Be sure to hold the drill steady and straight to create a clean and accurate pocket hole.


How can I cut a hole in the middle of wood?

To cut a hole in the middle of wood, you can use a drill with a hole saw attachment. Simply mark the center of the wood where you want the hole to be, then drill into the wood using the hole saw attachment until you reach the desired depth. Make sure to secure the wood properly before drilling to prevent any accidents.