0
Add your answer:
Earn +20 pts
How do you determine the square footage of stairs?
Assuming you want the square footage for 12ft wide broadloom carpet; a quick measure of the width of the stair tread (width), typical lineal measurement of both riser and down across stair tread and over and around stair nosing(LF), and total amount of stairs (each). An 8ft ceiling typically has 12 stair treads with 13 risers. Stair tread and riser measure typically 1'6" LF and 1'9" LF allows for tucking and squaring the piece. A typical width is 3'2" wide. Thus you can get 3 widths out of a 12ft wide carpet. Needing 12 stairs x 3'2" wide x 1'9" LF in total. A 12 ft wide carpet running (4 x 1'9" LF) 7'0" . You need 12'0" x 7'0" or 9.33 Sq.yards/84 Sq.feet. If you have "pie shaped" stairs you have to measure the furthest points of both riser and stair tread while measuring the stair tread on a 90 degree angle to the riser so the straightness of the pile direction is consistant from stair to stair regardless of the shape of the stair. Stairs that are opened on the sides( no stringer) must also be measured along furthest points and allow extra tuck space for upholstery of the corners. If the stairs are wider then 4 feet, use a piece of graph paper to draw out the 12 ft width of carpet and "fill-in" the stairs allowing 1"-3" in between cut pieces. Always allow an extra 3" per total cut size to allow for the factory cut to be off-square!
How many stair in a flight of stair?
2756
A stairs has a total rise of 10 feet and it has 15 threads and 16 risers What is the riser height?
The riser would be 7 1/2" or 187mm.
What is the function of stair gates?
A Stair Gates Main Function is Safety and Baby Safety. Most Houses get these when there is a baby and/or toddler. Stair Gates block a person from going up or down the stairs.
What is a homonym for stair?
Stare.
What is the difference between stair tread and stair riser?
The tread is what you step on, the riser is the part going up. Rise=riserThe tread is what you step on. The riser is the upright piece your toe hits.
What is the part of the stair you don't step on called?
The part of the stair you don't step on is called the riser. It is the vertical section that connects each step.
What is riser and trade in architecture?
trade and riser are the terms used for stair case. trade is used for the breadth of and riser is used for height of stairs.
How do you layout a stair?
Minimum tread is 10" and maximum riser is 7.75".
What is a horizontal ridge like a stair step called?
Waka flacka. you do not step on the riser
What is the proper overhang for a stair tread over the riser?
No more than 1-1/4 inch.
What is the minimum height for a stair riser?
Six foot and eight inches is usually code, but check codes locally.
What is rise of stair?
The rise of a stair is the vertical distance between the treads. The term can be used for the height of the full set of stairs. A riser is the vertical board running along the front of the step.
What are all the Stair parts?
Tread, riser, stringer, spindle, newel post, hand rail. fillet, shoe moulding, dowelling, screws, glue.
What is a stair piece?
stringer is the support piece, usually under both sides and one in the middle riser is the front piece tread is the flat piece you walk on
Parts of a stair?
you step on the TREADThe RISER holds the treads-- the riser is the zig / zag part where the treads lay on.The riser backboard is the face plate you see as you walk up the stairs and your toes hit on.The Knewal is the post at the top or the bottom of the banister / railingThe ballistars are the poles that are placed under the railing that follow from top to bottom.
Where do you measure from to determine the height of a stair hand rail?
Measure from the nose and the top of the tread of the plumb up the wall 34' to 36'
