0
Add your answer:
Earn +20 pts
What does 2deep rule mean?
The "2-deep" rule means that a building should have only the main distribution and the intermediate distribution that feeds the horizontal distribution to the work area.
What is the basic principle of vernier caliper?
One of the main divisions are sub-divisions.
What is main function of distribution bars?
Distribution bars allow a vehicle to pull more weight without damaging the rear axle or interfering with steering. They function by adding some leverage to both sides of the hitch, which allows for more even distribution of the load's weight.
Does The South Arcot Electricity distribution Co ltd. of Madras exist?
No, it was taken over by the Government of Madras State by an Enactment in 1954 and became part of the Madras State Electricty Board (now Tamil Nadu Electricity Board) circa 1957-59.
Is normal distribution also a probability distribution?
Yes. When we refer to the normal distribution, we are referring to a probability distribution. When we specify the equation of a continuous distribution, such as the normal distribution, we refer to the equation as a probability density function.
Can you connect final Distribution board directly to Main Distribution Board without Sub main Distribution Board and why?
yes no problem
What is the difference between Sub Main Distribution Board and distribution board?
main db using mcb sub main db using mccb that is deference
What is SDB and SMDB in electrical?
SDB stands for Sub-Distribution Board, which is a panel that receives power from the main distribution board and distributes it to various electrical circuits. SMDB stands for Sub-Main Distribution Board, which is a larger panel that receives power directly from the main distribution board and distributes it to multiple sub-distribution boards.
What is MDB and SMDB in electrical?
MDB= Main Distribution Board, it is usually fed from a substation and supplies electricity to a Sub Main Distribution Board ( SMDB ) The SMDB goes on to supply electricity for a panel
What is mean by 7segment distribution board?
A distribution board which has 7 segments , one for Main incomer, three as sub incomer for each phase and three for singlephase outgoing is called a 7 segment DB
What is the full name for MDB?
Main distribution board
What is radial distribution system?
There are 3 type of power distribution namely loop,network and radial.Radial distribution is the type of power distribution where the power is delivered from the main branch to sub-branches then it split out from the sub-branches again. it is the cheapest but least reliable network configuration.
What are the main components of a household circuit?
MAIN COMPONENTS (HOUSE HOLD CIRCUIT)1. METER2. MAIN SWITCH3. PANEL BOARD4. SOCKETS5. LOADS~> C.A.P.T.A.I.N D.A.R.NA ! xD
What is the names of motherboards?
The other names of "motherboard" are main board, system board, planar board & logic board. Because, a mother board contains significant sub- system such as the process and other components. It is the main printed circuit board. It holds many of the crucial electronics components of the system such as CPU, memory and provides connectors for other peripherals. networkrepairs.ca
What is another name for a motherboard?
The other names of "motherboard" are main board, system board, planar board & logic board. Because, a mother board contains significant sub- system such as the process and other components. It is the main printed circuit board. It holds many of the crucial electronics components of the system such as CPU, memory and provides connectors for other peripherals. networkrepairs.ca
What do you call the board where the splices and joints are presented?
distribution board
Does a sub panel need a main breaker?
Answer for Canada, USA and countries running a 60 Hz, 120/240 volt, split supply service.The main distribution panelboard has to have a main disconnect. This has been in the electrical regulations since the late 50's.If the sub panel is in the same home under the same roof line, the sub panel enclosure does not need a main disconnect because it is just another branch circuit. Connecting a sub panel to a separate free standing garage or workshop is a different scenario and is governed by a different set of electrical code regulations.What needs to be done to the panelboard is physically remove the neutral bonding screw. This is the screw that bonds the panelboard enclosure to the neutral bus. By doing this it stops a secondary ground pathway for a fault current from the sub panelboard to flow back to the main panelboard on the sub panel's neutral feeder.The electrical code requires that there is only one position on an electrical distribution service where the distribution enclosure and the neutral bus join each other. That is at the main disconnect of the first over current device, which is the main service disconnect breaker or a fused disconnect switch whichever your system uses..
