0
What is answer Curved surface area of a cylinder is 176cm square area of base is 38.5cm square fund volume?
To find the volume of the cylinder, we can use the formula for the curved surface area (CSA) and the area of the base. The CSA is given by ( CSA = 2\pi rh ), and the area of the base is ( A = \pi r^2 ). From the base area, we can find the radius ( r ), and then use the CSA to find the height ( h ). Finally, the volume ( V ) of the cylinder is given by ( V = A \times h ).
Given CSA = 176 cm² and area of base = 38.5 cm², we have:
- ( r^2 = \frac{38.5}{\pi} ) which gives ( r \approx 3.5 ) cm.
- Using ( CSA = 2\pi rh ), we can solve for ( h ) and then calculate ( V = A \times h ) to find the volume.
After these calculations, the volume of the cylinder is approximately 134.5 cm³.
What else can I help you with?
Explain Why is the surface of water in a graduated cylinder curved?
it is probably called figure it out, it is curved because glass is sticky. When you measure the volume from a graduated cylinder, measure at the bottom of it. It is called the meniscus.
What is the volume of a cylinder whose curved surface has an area of 377 square cm and a height of 15 cm?
2*pi*r*h=area of curved surface 377=2*3.1428*r*15 r= 4cm Volume=pi*r*r*h 3.1428*16*15 754.27 cubic cm
How are a cylinder and a squared based pyramid alike and different?
A cylinder and a square-based pyramid are alike in that both are three-dimensional geometric shapes and can be described using volume and surface area formulas. However, they differ in their bases and shapes: a cylinder has circular bases connected by a curved surface, while a square-based pyramid has a square base and triangular faces that converge to a point at the top. Additionally, the cylinder has uniform cross-sections along its height, whereas the pyramid's cross-section changes from the square base to the apex.
How would you find the surface area of a cylinder with circle bored out of it?
Actually, answer 1 is for the volume, not the surface area. Aside from that, there are lots of ways to bore a hole in a cylinder. If it goes from one base (a flat face) to the other (or part of the way) parallel to the axis, answer 1 is correct (for the volume). If it is not parallel to the axis, or if it is bored from the curved surface of the cylinder, it is much more complicated. Assuming, as in answer 1, that the hole goes all the way from one base to the other parallel to the axis, to get the surface area you would add the surface area of the outer cylinder to that of the hole (just the curved surface portion), and then subtract the areas of the circular holes in the two bases, each of which is pi x the radius of the hole squared. I'm assuming you know how to calculate the surface area of a cylinder. This is the area of the curved surface, which is 2 x pi x the radius x the height, plus 2 x the area of each base, which is pi x the radius squared. ========================================================== Use the formula:- Volume of a cylinder = Pi X Radius squared X Length , to find the volume of a solid cylinder. Repeat the same calculation with the same formula, to find the Volume of the cylinder of fresh air within the cylinder . Subtract the fresh air Volume from the Solid Cylinder Volume. That will be your answer . Think about your problem, then it is dead easy.
Is the volume of a cylinder the same as the surface area of a cylinder?
no
Where do you measure the volume of a liquid on a graduated cylinder?
You measure the volume of a liquid on a graduated cylinder at the meniscus, which is the curved surface of the liquid.
What are the properties of a cylinder filled with water?
A cylinder filled with water has properties such as volume, surface area, and weight. The volume of water in the cylinder is determined by its height and radius. The surface area of the cylinder is the total area of its curved surface and two circular bases. The weight of the water in the cylinder is influenced by its volume and density.
Explain Why is the surface of water in a graduated cylinder curved?
it is probably called figure it out, it is curved because glass is sticky. When you measure the volume from a graduated cylinder, measure at the bottom of it. It is called the meniscus.
What formula do you use to measure a cylinder?
if u r talking about its volume then its formula is 22/7 . square of radius . height and its curved surface area is 22/7 r l
Cylinder volume equals 250 cm3 curved surface area equals 150 cm2 what is the height?
1
What is the volume of a cylinder whose curved surface has an area of 377 square cm and a height of 15 cm?
2*pi*r*h=area of curved surface 377=2*3.1428*r*15 r= 4cm Volume=pi*r*r*h 3.1428*16*15 754.27 cubic cm
How can you use volume and meniscus in the same sentence?
To accurately measure the volume of a liquid in a graduated cylinder, you must read the measurement at the bottom of the meniscus, which is the curved surface of the liquid caused by surface tension.
How do you measure the volume of a liquid using a graduated cylinder?
To measure the volume of a liquid using a graduated cylinder, you simply pour the liquid into the cylinder and read the measurement at the bottom of the meniscus, which is the curved surface of the liquid. The volume is typically measured in milliliters (mL) or cubic centimeters (cm).
How to find the volume of a curved cylinder?
a way is you can use Archemedes principle and fill a glass of water bigger than the cylinder to the top. then place the glass in a bowl. carefully place the cylinder in the glass and make sure you submerge the whole cylinder.take the bowl with the water in it and pour it into a measuring cup and see how much water it is. that will be the volume of the cylinder.
How are a cylinder and a squared based pyramid alike and different?
A cylinder and a square-based pyramid are alike in that both are three-dimensional geometric shapes and can be described using volume and surface area formulas. However, they differ in their bases and shapes: a cylinder has circular bases connected by a curved surface, while a square-based pyramid has a square base and triangular faces that converge to a point at the top. Additionally, the cylinder has uniform cross-sections along its height, whereas the pyramid's cross-section changes from the square base to the apex.
How would you find the surface area of a cylinder with circle bored out of it?
Actually, answer 1 is for the volume, not the surface area. Aside from that, there are lots of ways to bore a hole in a cylinder. If it goes from one base (a flat face) to the other (or part of the way) parallel to the axis, answer 1 is correct (for the volume). If it is not parallel to the axis, or if it is bored from the curved surface of the cylinder, it is much more complicated. Assuming, as in answer 1, that the hole goes all the way from one base to the other parallel to the axis, to get the surface area you would add the surface area of the outer cylinder to that of the hole (just the curved surface portion), and then subtract the areas of the circular holes in the two bases, each of which is pi x the radius of the hole squared. I'm assuming you know how to calculate the surface area of a cylinder. This is the area of the curved surface, which is 2 x pi x the radius x the height, plus 2 x the area of each base, which is pi x the radius squared. ========================================================== Use the formula:- Volume of a cylinder = Pi X Radius squared X Length , to find the volume of a solid cylinder. Repeat the same calculation with the same formula, to find the Volume of the cylinder of fresh air within the cylinder . Subtract the fresh air Volume from the Solid Cylinder Volume. That will be your answer . Think about your problem, then it is dead easy.
Are correct procedures for reading the volume of water in the graduated cylinder?
Water in a glass graduated cylinder adheres to the sides of the cylinder, forming a meniscus which is an upward curve. When reading volume in a cylinder, look at the meniscus at eye level. Read the volume at the bottom of the curve.
