0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Which of the following troubleshooting steps usually takes place after you have talked to the user experiencing the problem?
Gathering information on the issue
How do you evaluate?
You evaluate a class, performance or skill based on the basic requirements (aka rubric) for that effort. It is like a report card. So, for work you would say you are a hard worker (available for overtime, multi-tasking skills), are great at job duties (what you do best--troubleshooting, fast assembly, rapport with the customer) and so on. So, set up your rubric and then state your abilities for each item.
A 1999 Yamaha Grizzly has no spark and the dealer spent several hours trying to find the problem with no results Any ideas?
Get a new dealer I do agree with the above answer as well, but... This is from my repair manual for a 2006 Grizzly 660. IGNITION SYSTEM ELEC TROUBLESHOOTING IF THE IGNITION SYSTEM FAILS TO OPERATE (NO SPARK OR INTERMITTENT SPARK Procedure Check: 1.Fuse (main, ignition) 2.Battery 3.Spark plug 4.Ignition spark gap 5.Spark plug cap resistance 6.Ignition coil resistance 7.Engine stop switch 8.Main switch 9.Pickup coil resistance 10.Charging/rotor rotation direction detection coil resistance 11.Wiring connection (the entire ignition system) NOTE: Remove the following part(s) before troubleshooting: 1)Seat 2)Fuel tank side panels 3)Front carrier 4)Front fender Use the following special tool(s) for troubleshooting. Dynamic spark tester: P/N. YM-34487Ignition checker: P/N. 90890-06754 Pocket tester: P/N. YU-03112, 90890-03112 CONTINUITY 1.Fuse (main, ignition) Refer to "CHECKING THE SWITCH". NO CONTINUITY Replace the fuse. CORRECT 2.Battery Check the battery condition. Refer to "CHECKING THE BATTERY" in CHAPTER 3. Open-circuit voltage: 12.8 V or more at 20 °C (68 °F) INCORRECT Clean the battery terminals. Recharge or replace the battery. 3.Spark plug Check the spark plug condition. Check the spark plug type. Check the spark plug gap.
How do you troubleshoot a negative reading in a power meter?
Well, isn't that an interesting challenge we have here! When you see a negative reading on a power meter, it could be a simple mix-up with the connections or a sign of reverse power flow. Take a deep breath, my friend, and gently double-check the connections and make sure everything is properly set up. If the issue persists, it might be a good idea to consult with a professional to help you find a peaceful solution.
What does a code 2d means on a Raymond?
A code 2D on a Raymond forklift typically indicates a low battery voltage fault. This means that the battery voltage is below the acceptable threshold for proper operation. It is important to address this issue promptly to avoid damage to the battery or other components of the forklift. Troubleshooting steps may include checking the battery connections, charging the battery, or replacing the battery if necessary.
What The various types of troubleshooting in computer?
there are three types of troubleshooting in computer hardware troubleshooting software troubleshooting peripheral troubleshooting
What is meant by troubleshooting?
Troubleshooting is a form of problem solving
Troubleshooting differs from diagnosis in that .?
troubleshooting focuses on how to fix the problem
Definition of troubleshooting of vehicle?
aah troubleshooting a vehicle is when your too drunk to hold the gun straight. then your having troubleshooting a vehicle.
Which troubleshooting model is best which is worst and why?
which troubleshooting model is the best and which one is the worst
What is the importance of troubleshooting?
the presence of troubleshooting makes it possible for failed products workable again.
You're troubleshooting a user's problem What is the first thing you should do when troubleshooting?
ascertain the user's priorities
What network troubleshooting tasks will a packet sniffer NOT help with?
a packet sniffer has unlimited troubleshooting tasks
What online site provides a troubleshooting guide for the iPad 3g?
Apple has a troubleshooting guide on their website as well as an online PDF of their manual. CNET is another website that would have troubleshooting for the iPad.
What TCP IP utility is commonly used on the command line of routers?
Two commonly used utilities, for troubleshooting, are ping and traceroute.Two commonly used utilities, for troubleshooting, are pingand traceroute.Two commonly used utilities, for troubleshooting, are pingand traceroute.Two commonly used utilities, for troubleshooting, are pingand traceroute.
What is the MAIN contribution of bookkeepers to troubleshooting corporate problems?
What is the MAIN contribution of bookkeepers to troubleshooting corporate problems?
What is the difference between troubleshooting and maintenance?
Troubleshooting is finding an existing problem and maintenance is preventing a potential problem.
