answersLogoWhite

0

What else can I help you with?

Continue Learning about Math & Arithmetic

How do you convert one cubic meter of natural gas into mm BTU?

To convert one cubic meter of natural gas to million British thermal units (mm BTU), you typically use the conversion factor that 1 cubic meter of natural gas is approximately equal to 35.3 MJ (megajoules). Since 1 mm BTU is equivalent to about 1,055 MJ, you can calculate the conversion as follows: 35.3 MJ divided by 1,055 MJ/mm BTU gives approximately 0.0334 mm BTU. Therefore, one cubic meter of natural gas is about 0.0334 mm BTU.


How many boilers can you run of a R 5 gas meter?

The number of boilers you can run off an R5 gas meter depends on the total gas consumption of the boilers and the capacity of the meter. An R5 gas meter typically has a maximum flow rate of around 6 cubic meters per hour. To determine how many boilers can be supported, you would need to calculate the total gas demand (in cubic meters per hour) of all the boilers combined and ensure it does not exceed the meter's capacity. Always consult with a qualified technician to ensure safe and efficient operation.


How many BTU in one cubic meter of CO gas?

There is no specific number of BTUs in one cubic meter of carbon monoxide (CO) gas. The amount of BTUs in a gas is determined by its composition and heating value, which can vary. However, carbon monoxide generally has a lower heating value compared to other gases like methane or propane.


How many kg oxygen gas capacity in 1 cubic meter volume?

Gas is compressible. As long as you can keep increasing the pressure, you can stuff as much oxygen into a bottle or a tank as you want to, until it bursts.


How do you convert BTU per lb to BTU per scf?

Btu / scf = Btu / lb X MW / 379.5 where: MW = molecular weight of the gas, lb / lb-mol The constant 379.5 is the molar volume at standard conditions of 14.696 psia and 60°F

Related Questions

How many btu per hours in 1 cubic meters?

One Cubic Meter of natural gas is approximately 36000 btu.


What size gas meter do you need for your house to use a 333000 BTU pool heater?

The gas meter on your house is sufficient,


How do you convert one cubic meter of natural gas into mm BTU?

To convert one cubic meter of natural gas to million British thermal units (mm BTU), you typically use the conversion factor that 1 cubic meter of natural gas is approximately equal to 35.3 MJ (megajoules). Since 1 mm BTU is equivalent to about 1,055 MJ, you can calculate the conversion as follows: 35.3 MJ divided by 1,055 MJ/mm BTU gives approximately 0.0334 mm BTU. Therefore, one cubic meter of natural gas is about 0.0334 mm BTU.


Does running a new line from your gas meter increase your BTU capability?

only if the new pipe is bigger in which case all pipe leading up too it must also be of sufficient BTU rating. So.... No. You'll most likely have to get a new gas line run to your house or a lot of meter work done. maybe meter would have to be replaced to allow height total btu capability.


How many Btu's in 1 pound of natural gas?

The average is about 20,000 BTU's per pound at standard temperature and pressure.


Can 250 CFH gas meter supply a house with a gas furnace and a 200000 BTU water heater?

If your furnace is less then 50000btus then yes.


How many cf of gas in 1750 Mbtu if gas?

Natural gas has a heating value of about 1,000 BTU/ft3 (gross) or about 900 BTU/ft3 (net). Acttual values can range about 100 BTU/ft3 higher or lower than the average. So 1,750x106 BTU would be about 2,000 ft3


What size gas heater should you buy for a 27' above ground pool in Upstate New York?

400,000 btu's minimum ...pat What Pat is not considering is the size of your gas meter or the gas line to the equipment pad if there is one. If you are starting from scratch you still need to know the gas meter size and the length and diameter of the gas run. Absolutely critical to heater installations. Because of the existing gas line and meter you may be limited as to the size or BTU of the heater. k


What size gas meter do you need for a house that has 200000 BTU heater?

Check with your utility company; you may have other gas utilities in use as well.


What is the average BTU for a residential oven?

Not all double gas wall ovens have the same number of BTUs. For instance, BlueStar makes a double gas wall oven that has a 25,000 BTU burner and one that has a 30,000 BTU burner.


What is the purpose of installation BTU Meter in LPG?

The purpose of installing a BTU meter in LPG (liquefied petroleum gas) systems is to measure the energy content of the gas being consumed. This allows for accurate billing based on the actual energy consumed rather than just the volume of gas. It also helps in monitoring energy usage and identifying potential efficiency improvements.


How many BTU of gas come in to a house from the gas meter?

The amount of BTUs of gas entering a house from the gas meter can vary depending on factors such as the size of the meter, the gas pressure, and the flow rate. Typically, residential gas meters measure gas usage in cubic feet or cubic meters, and this can be converted to BTUs using a conversion factor provided by the gas utility company.