answersLogoWhite

0


Best Answer

XXXXXXXXX=Horizontal

X

X

X

X

X

X

X=Vertical.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the difference between horizontal shaft and vertical?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Math & Arithmetic

What is the Difference between horizontal and vertical engine?

Vertical engines produce more power than horizontal engines and horizontal engine has less power than vertical engines and horizontal engines are especially designed for better mileage Not sure about mileage but the big difference is vertical shaft goes like this | and the horizontal shaft goes like this ---- . > Lower centre of gravity.


What is the difference between a drift and slope mine?

Drift mines are characterized by the use of a level tunnel leading into the mine, while slope mines have an inclined tunnel, and shaft mines utilize a vertical tunnel


How the cone crusher works?

Cone crusher crushes materials by the working surface between the movable cone and fixed cone. The movable cone is supported by spherical bearing and fixed on an hanging erect shaft which is set in the eccentric sleeve, and the sleeve is set on the stopping and pushing bearing. The movable cone and erect shaft are driven by the eccentric shaft sleeve together. The eccentric shaft sleeve is driven by horizontal shaft and fimbriated gear, and the wheel of the conveyor belt is driven by motor through v-belts. The lower part of vertical shaft is installed in the eccentric sleeve. When the eccentric sleeve rotates, there is a conical surface lined out by the shaft. When the movable cone comes near the fixed cone, rocks are grinded into pieces, when the cone leaves, grinded materials is discharged from the discharge hole. The fixed cone can be ascended or descended by adjusting setting to adjust the width of discharge hole, consequently the output size is determined.


What is a step angle?

The nominal angle through which the step motor shaft rotates between adjacent step positions.


Are thrust loads at a right angle to a shaft?

On a ships propeller shaft, the thrust will be in line with the axis of the shaft.

Related questions

What is the Difference between horizontal and vertical engine?

Vertical engines produce more power than horizontal engines and horizontal engine has less power than vertical engines and horizontal engines are especially designed for better mileage Not sure about mileage but the big difference is vertical shaft goes like this | and the horizontal shaft goes like this ---- . > Lower centre of gravity.


What is a vertical shaft engine?

Drive shaft is vertical- like a lawnmower. Cylinder is horizontal.


What is difference between penstock and pressure shaft?

A penstock is a pipe that carries water from the reservoir to the turbine in a hydroelectric power plant, while a pressure shaft is a vertical pipe that carries water under pressure from the penstock to the turbines. The penstock is typically horizontal and submerged in water, while the pressure shaft is vertical and carries water at high pressure.


What are the 3 uses of Gears?

Gears can change direction of rotational force from one axis to another. For example, a wind driven mill. The wind turns a shaft that is horizontal. That shaft turns a gear that is vertical, and the vertical gear meshes with a horizontal gear that turns a vertical shaft. Gears can change rotational speed. With a small gear meshed and turning a larger gear, the larger gear will have a slower RPM. Gears can change torque to increase or decrease available power. A small low force gear driving a larger gear will provide more rotational force.


How do outboard motors work?

The top part of an outboard houses the engine. Most older models used a two stroke type where oil is mixed with the gas. The engines' vertical drive shaft is the slim middle part. At the bottom, a gear converts the vertical motion of the shaft to a horizontal one, to which is connected the propeller.


How much horsepower in Honda 160 cc lawnmower engine?

Honda makes more than one type 160cc engine. The GC160 horizontal shaft outputs 5 h.p. The vertical shaft engine outputs 4.8 h.p.


What is a mine shaft?

Shaft mining or shaft sinking refers to the method of excavating a vertical or near-vertical tunnel from the top down, where there is initially no access to the bottom.


What is the difference between a drift and slope mine?

Drift mines are characterized by the use of a level tunnel leading into the mine, while slope mines have an inclined tunnel, and shaft mines utilize a vertical tunnel


What is the entrance or opening to a mine called?

An adit. In North America, the horizontal or sloped entrance to a mine is called a "Portal". Portal more specifically refers to the portion of the shaft visible from the outside of the mine. In some areas, the Portal portion of a horizontal shaft is called the "Drift Mouth" or "Drift Portal" as this shaft leads into a "Drift Mine". With a vertical shaft, that portion would be called a "Collar".


What is an air shaft?

An air shaft is a vertical shaft which supplies ventilation to a tunnel or underground facility.


What is the difference between a 350 Chevy crank shaft and a 400 crank shaft?

400 has a longer stroke


What type of cave is the cave of swallows BESIDES pit?

pit cave, shaft cave or vertical cave. it is a type of natural cave which contains one or more significant vertical shafts rather than being predominantly a conventional horizontal cave passage