0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the measure of RST?
44
What is the measure of rst 46?
23
If RST RS 15 RT 12 and ST 17. Which angle of RST has the smallest measure?
The angle opposite side RT = 12 will have the smallest measure
Perimeter of rst equals 32cm find the perimeter of jkl?
48
Perimeter of rst equals 32 cm find the perimeter of jkl?
48
What is the use of Interrupt vector table of 8086 microprocessor?
The interrupt vector table in the 8085 is a region of low memory that contains the target addresses for the RST instructions. RST can be invoked by the program, by an INTR request which provides an RST x instruction in response to INTA, or by one of the four direct interrupt pins, TRAP, RST5.5, RST6.5, and RST7.5 Each of these interrupt sequences place the PC on the stack, and then execution goes to one of the vectors. The vectors are as follows... RST 0: 0000H RST 1: 0008H RST 2: 0010H RST 3: 0018H RST 4: 0020H TRAP: 0024H RST 5: 0028H RST5.5: 002CH RST 6: 0030H RST6.5: 0034H RST7: 0038H RST7.5: 003CH
Why rst x.1 rst x.2 rst x.3 not in 8085 why only rstx.5 is used?
Because that's how Intel designed the 8085. In addition to the 8080 type interrupt on the INTR pin, Intel chose, for the 8085, to implement four new interrupts, RST 5.5, RST 6.5, RST 7.5, and TRAP, each of which would not require the interrupting device to provide a vector. The naming convention of x.5 was simply in recognition that Intel placed the implicit vector halfway between two other RST vectors. As an example, RST 6.5 is halfway between RST 6 and RST 7. Since RST 6 and RST 5 are eight bytes away from each other, placing RST 6.5 in between would place a limit of four bytes, and four bytes is enough to place a three byte JMP instruction. The decimal and hex addresses of all of the vectors are... RST 0 - 0 - 00H RST 1 - 8 - 08H RST 2 - 16 - 10H RST 3 - 24 - 18H RST 4 - 32 - 20H TRAP - 36 - 24H RST 5 - 40 - 28H RST 5.5 - 44 - 2CH RST 6 - 48 - 30H RST 6.5 - 52 - 34H RST 7 - 56 - 38H RST 7.5 - 60 - 3CH
What does 5.5 mean in RST 5.5 interrupt of 8085 microprocessor?
The 5.5 in RST 5.5 means that the interrupt vector is located between RST 5 and RST 6.
What is RST in 8085?
RST OF TRAP is 24h(hexadecimail) address.
Why specific name of interrupt RST?
Because this mnemonic stands for RESTART (RST).
In RST RS 15 RT 12 and ST 17. Which angle of RST has the smallest measure?
It is angle RST.
In what year did Rosetta Stone - RST - have its IPO?
Rosetta Stone (RST)had its IPO in 2009.
what- for RST?
false
RST is dilated?
answer
What is the interrupt number in 8085 microprocessor and how to find interrupt's vector address?
The 8085 has five interrupts, INTR, RST5.5, RST6.5, RST7.5, and TRAP. It also has eight software interrupts, RST0, RST1, ..., RST7. The INTR interrupt requires a hardware response that is an opcode. Usually, the opcode is either a CALL instruction, in which case the interrupt vector can go anywhere in memory, or it is an RST instruction, in which case the vector is based on a table in low memory. In the case of RST instructions, either directly or via INTR, or the RSTx.5 interrupts, you simply multiply the interrupt number by 8 to get the vector address. The following table presents the vector addresses for all possible interrupts... RST 0 - 00H RST 1 - 08H RST 2 - 10H RST 3 - 18H RST 4 - 20H TRAP - 24H RST 5 - 28H RST5.5 - 2CH RST 6 - 30H RST 6.5 - 34H RST 7 - 38H RST 7.5 - 3CH
What does rst in 8085 software interrupt stand for?
RST is simply the opcode chosen to represent the Restart instruction.
What does 6.5 signify in rst 6.5 of 8085 microprocessor?
The name, RST6.5, was chosen because the interrupt vector lies halfway between RST 6 and RST 7, specifically at address 0034H.
