0
The take-up amount for a stub-up bend using a 1-inch Intermediate Metal Conduit (IMC) is typically around 6 inches. This measurement allows for the proper fitting and installation of the conduit when making a bend to connect to an electrical box or another conduit run. However, it's essential to consult specific local codes or installation guidelines, as these can vary.
What else can I help you with?
What do you subtract if you are using a 1 inch emt bender?
When using a 1-inch EMT bender, you typically subtract 2 inches from the total length of the conduit for each bend. This accounts for the radius of the bend, which is usually 3 inches for a 1-inch EMT bender. Therefore, if you are planning to make a bend, measure the distance you want to bend from the end of the conduit and subtract 2 inches to ensure the proper length.
How many inches do you deduct on a 90 degree bend on half inch bend?
6 inches
What force is needed to bend 1.5 inch square in tubing?
it depends on both the tube wall thickness and the length of the bend and how much you bend it. Otherwise you cannot determine force.
How many inches do you deduct for a 90 degree bend on a 1 inch conduit?
4
How many inches do you deduct for on a 90 degree bend on inch and a half conduit?
For a 90-degree bend on 1.5-inch conduit, you typically deduct 10 inches from the total length of the conduit. This deduction accounts for the bend's radius and allows for proper installation. Always refer to local codes and guidelines, as requirements may vary.
What is the take up amount for a stub up bend using 1 inch imc?
11''
What do you subtract if you are using a 1 inch emt bender?
When using a 1-inch EMT bender, you typically subtract 2 inches from the total length of the conduit for each bend. This accounts for the radius of the bend, which is usually 3 inches for a 1-inch EMT bender. Therefore, if you are planning to make a bend, measure the distance you want to bend from the end of the conduit and subtract 2 inches to ensure the proper length.
Can a woman bend a 1 inch steel bar in a vise?
depends on what you mean by " bend" take a 20' bar ,stick it in a 10" vise and it will " bend " by itself take a 10" bar ,stick it in a vise and put a torch to it ,and a child can bend it so.... can a woman bend a 1" steel bar? Probably if she puts her mind to it.
How far from the end of the conduit should you put the mark that will line up with the bender arrow if you are using 12-inch EMT and a hand bender and you want to make a bend with a 14-inch stub-up?
For a 14-inch stub-up using a 12-inch EMT and a hand bender, you should mark the conduit 10 inches from the end of the conduit to align with the bender arrow. This accounts for the 14-inch stub-up and the 4-inch radius of the bend. Always verify the dimensions based on your specific bender's markings before proceeding.
What if your making a 90 degree bend on12 inch conduit if your conduit bender has a 5 inch take up and you need a 13 inch rise how far from the starting point would you place your bend mark?
using half inch conduit for a 13 in 90, the bender takes up 5 inches so you subtract 5 inches from 13 inches and place the arrow at 8 inches.
How many inches do you deduct on a 90 degree bend on half inch bend?
6 inches
Using 12 inch EMT and a hand bender you want to make a bend with a 14 inch stub up How far from the end of the conduit should you put the mark that will line up with the bender arrow?
1/4"
What an inch?
Bend your thumb-the top part. DIAGRAM l = thumb - <----- an inch (top part of thumb) `
What makes an inch?
Bend your thumb-the top part. DIAGRAM l = thumb - <----- an inch (top part of thumb) `
What force is needed to bend 1.5 inch square in tubing?
it depends on both the tube wall thickness and the length of the bend and how much you bend it. Otherwise you cannot determine force.
A hand-operated conduit bender with a shoe for bending 1-inch EMT can also be used to bend?
1/2 inch emt
How many inches do you deduct for a 90 degree bend on a 1 inch conduit?
4
