0
What else can I help you with?
Does the math term ratio mean multiply?
No, the math term ratio doesn't mean multiply.
What is the common ratio of the geometric progression?
The common ratio is the ratio of the nth term (n > 1) to the (n-1)th term. For the progression to be geometric, this ratio must be a non-zero constant.
How can you identify whether a ratio is a rate?
The second term in the ratio is 1.
Which sequence is a geometric sequence having 4 as its first term and 3 as the common ratio?
You start with the number 4, then multiply with the "common ratio" to get the next term. That, in turn, is multiplied by the common ratio to get the next term, etc.
What is the ratio 15 to 5 in lowest terms?
The lowest term is a ratio of 3:1
What is the defined term of strain?
In physics, strain refers to the deformation or displacement of a material due to applied stress. It is a measure of how much a material deforms under loading compared to its original shape. Strain can be expressed as a ratio or percentage of the change in size or shape of an object.
What is the difference between Young's modulus and elastic modulus?
Young's modulus and elastic modulus are often used interchangeably, but there is a subtle difference between the two. Young's modulus specifically refers to the ratio of stress to strain in the elastic region of a material's stress-strain curve, while elastic modulus is a more general term that can refer to any modulus of elasticity that describes a material's ability to deform elastically under stress.
The term that refers to the force that acts on rock to change it's shape or volume?
stress
What is meant by the term contribution margin ratio?
The term contribution margin ratio is the percentage of contribution over total revenue. It is used in cost-volume-profit analysis, a form of management accounting.
What is ultimate load method?
In ultimate load method, the working loads are increased by suitable factors to obtain ultimate loads. These factors are called load factors. The structure is then designed to resist the desired ultimate loads. This structure is then designed to resist the desired ultimate loads. This method takes into account the non-linear stress-strain behavior of concrete. The term safety factor has been used in the working stress method to denote the ratio between the yield stress and the permissible stress. It had little meaning as far as the ratio between collapse loads and working load was concerned. The team load factor has been traditionally used to denote the ratio between the collapse or ultimate load to the working load. The knowledge of load factor is more important than the knowledge of factor of safety. Several ultimate load theories have been proposed in the past. In each of these theories and idealized stress-strain curve has been adopted for concrete which is the only difference among them. This theory is based on the assumption that ultimate strain in concrete is 0.3% and the compressive stress at the extreme edge of the section corresponds to this strain. Whitney replaced the actual parabolic stress diagram by a rectangular stress diagram such that the centre of gravity of both diagrams lies lat the same point and their areas are also equal.
What term means to twist and pull a muscle or tendon?
Its called a strain
What is the first term in a ratio?
Antecedent is the first term in a ratio .
What is gel space ratio?
Gel is the hydrated cement while space is volume occupied by hydrated cement+capillary pores. Hence gel/space ratio is the fraction of volume occupied by hydrated cement in the total space occupied by hydrated cement and capillary pores
What is saccharomyces strain?
saccharomyces are fungi, strain in bioligal term are animal use for experimental purpose.
What is a ratio whose second term is 100?
A ratio is a comparison of two quantities. When the second term of a ratio is 100, it means that the ratio is comparing the first term to 100. For example, if the ratio is 1:100, it means the first term is 1 and the second term is 100. Ratios with a second term of 100 are often used to express proportions or percentages.
Does the math term ratio mean multiply?
No, the math term ratio doesn't mean multiply.
What was the condition of being out of work?
Being out of work refers to the state of unemployment, meaning the individual does not have a job or source of income. This condition can be temporary or long-term, and may lead to financial strain and emotional stress.
