0
What else can I help you with?
What is the tolerance for a 6.35 H7 hole?
The tolerance for a 6.35 H7 hole is defined by the H7 system, which specifies a certain range of limits for the hole's diameter. For a 6.35 mm nominal size, the H7 tolerance range typically allows for a hole diameter of 6.35 mm +0.025 mm to +0.000 mm, meaning the diameter can range from 6.35 mm to 6.375 mm. This tolerance ensures a precise fit, suitable for applications requiring a specific clearance or interference fit with corresponding shafts.
What is the diameter of a goal hole?
4.25 inches
What is radius of a 40 diameter hole?
the answer is 20
A hole in an aluminum plate has a diameter of 1.179cm at 23 Celsius What is the diameter of the hole at 198 Celsius and what temperature is the diameter of the hole equal to 1.177 cm?
L=L(initial)[1+C(al)]*T =1.184cm I can't figure out the second one either
How much dirt is in a hole ten inches deep and ten inches diameter?
None. There is nothing in a hole.
What is the tolerance for a diameter 30H7 hole?
+0.021 -0.00
What is the tolerance for a 6.35 H7 hole?
The tolerance for a 6.35 H7 hole is defined by the H7 system, which specifies a certain range of limits for the hole's diameter. For a 6.35 mm nominal size, the H7 tolerance range typically allows for a hole diameter of 6.35 mm +0.025 mm to +0.000 mm, meaning the diameter can range from 6.35 mm to 6.375 mm. This tolerance ensures a precise fit, suitable for applications requiring a specific clearance or interference fit with corresponding shafts.
H6 Tolerance for a 95mm hole?
H6 tolerance for 95 mm hole is +0.022/0
What does h stand for in tolerance?
h stands for standard hole in tolerance
What is diameter indent?
A diameter indent is a measurement feature on a part or component that specifies the desired diameter that a circular feature, such as a hole or boss, should have. This dimension helps ensure proper fit and alignment of mating parts during assembly. Manufacturers use diameter indents to accurately control the size and tolerance of circular features in mechanical components.
What differences are between tolerances of size and tolerances of position?
Tolerance in size is the allowable amount of change in dimension. For example, you want to fabricate a shaft that is 2 cm in diameter plus or minus 2 millimeters. The 2 millimeters is the tolerance. Tolerance in position is the allowable amount of change in position. For example, you need to drill a hole in a wall and you drew a point in the place you want to drill, you are allowed to move as far as 2 millimeters from that hole to receive satisfactory results, this is a tolerance of 2 millimeters in position
What was Gene Sarazens suggestion to increase the diameter of the hole for golf?
4.24563 inches is the diameter of a golf hole.
What is the tolerance for a 62mm H7 hole?
Tolerances H7 23DIA for hile is +0.021/-0.000 ///MUKI
What is hole and shaft basis system?
The hole and shaft basis system are pre-defined tables / methods in which you use to find tolerances. If you have a set hole size and wish to find the shaft diameter and tolerance required you would use the hole basis system. If you had a shaft at a set size and needed to find the hole size and tolerance required for it you would use the shaft basis system. If you need any more info on it you could try and google it or look it up in something like the machinist handbook (probable google it aswell)
What is the diameter of hole in the center of a CD?
CD's have a diameter of 5.5 centimeters;)
What is the diameter d of the pinhole?
The diameter d of the pinhole is the width of the hole.
What size hole is a 10h7?
A 10h7 hole is designed with a basic size of 10 mm and a tolerance range of +0.033 mm to +0.058 mm. This means that the actual hole size could range from 10.033 mm to 10.058 mm.
