answersLogoWhite

0

What else can I help you with?

Continue Learning about Math & Arithmetic

What is measured at a colocation data center?

The building monitoring systems in a company are measured at a colocation data centre. The benefit of this is to be effective and efficient for the company.


How do figure how many rafters it take for a house?

The question must 1st be asked is "what spacing do you plan to use?" Local codes will apply of course. Up North spacing is closer than that of the South because of snow loads. 16 inches on center is a good number to use. You said rafters but I wonder if you meant trusses. Another problem with answering the question is the roof design. For a ranch style house you would simply multiply the length in feet by 3 and then divide that by 4 and add one for the end this will give you the number of trusses you need. For rafters you need to multiply your number by 2 and add 4 for the barge rafters.


What used to stand at ground zero?

Before the September 11 attacks in 2001, Ground Zero was the site of the World Trade Center in New York City, which included the iconic Twin Towers. The complex also housed several other buildings, including the World Trade Center 3 (the Marriott World Trade Center Hotel) and World Trade Center 4 (the South Plaza Building). The site was a major center for international trade and commerce. After the attacks, it was transformed into a memorial and the new One World Trade Center was built as part of the rebuilding efforts.


Why third building collapsed 9 11?

The third building that collapsed on September 11, 2001, was World Trade Center 7 (WTC 7). It was not directly struck by an airplane but was severely damaged by debris from the collapse of the nearby North Tower and by fires that burned for several hours. The building's structural integrity was compromised due to the fires, which caused the steel framework to weaken, ultimately leading to its collapse in the late afternoon. The event has been the subject of various investigations and discussions regarding fire safety and building design.


Where is center of mass of a sphere?

The center of mass of a sphere is its geometric center.

Related Questions

What is the standard spacing of a roof rafter?

Rafters are 16" on center. Trusses are 24" on center. Or 450mm & 600mm australia


What does 400 cc mean in building plans?

400 cc means 400 dimension units from CENTER to CENTER For example, on a building Plan View_you will see lines running thru the center of the walls, if you look at the dimension line located at the top or side of a drawing, you'll see numbers between those lines. this means that the drawing was set out without thickness, so the measurements are therefore center to center. In real space the room is smaller than the cc size by Two Halves of the wall thickness. hth


What is the center thickness of a javelin?

37 meters


How does the thickness of the cornea compare to thickness of the sclera?

The sclera is double the thickness of the cornea. The center of the cornea is thinnest, followed by the periphery, then sclera.


How does the thickness of the sclera compare to the thickness of the cornea?

The sclera is double the thickness of the cornea. The center of the cornea is thinnest, followed by the periphery, then sclera.


What are floor trusses generally spaced to?

In Europe, CC (center center distance) is standardized at 600mm (about 24") which is what I expect the non-metric nations to consider good too!


What does the span rating on a sheet off plywood indicate?

It's the maximum on-center (O.C.) spacing (in inches) of studs/rafters/joists that the sheathing is being attached to. Face grain of plywood is to be perpendicular to the framing members. Sometimes two span ratings are included. If that's the case, the larger number is the O.C. inches for roof sheathing use, and the smaller is for subfloor sheathing use.


The center of gravity of a triangle solid with uniform thickness and density is at the intersection of the of the triangle?

The center of gravity of a triangle can be found by adjusting the thickness. You also need to find the density at the intersection.


When was New Center Building created?

New Center Building was created in 1930.


When was Shinjuku Center Building created?

Shinjuku Center Building was created in 1979.


When was Textile Center Building created?

Textile Center Building was created in 1926.


What is the live load capacity of a roof framed with 2x4 rafters 2 feet on center?

You still need to indicate the pitch, the roof sheathing, and the shingle weight.