0
What else can I help you with?
What size beam will span 18 feet?
That question cannot be answered without knowing the load on the beam.
What do you need for a beam run of 20 feet in basement with an even load on upper floor 2 story 16 on center 2 by 8 const with full span trussesno load on floors?
For a beam run of 20 feet in a basement with an even load from a two-story structure using 2x8 construction spaced 16 inches on center, you’ll need to determine the appropriate beam size and material to support the load safely. Typically, a structural engineer would recommend a beam made of either engineered wood (like LVL or glulam) or steel, depending on the specific load calculations. Additionally, you’ll need to consider factors like local building codes and any necessary supports or footings for the beam. Always consult with a professional for accurate sizing and compliance with safety regulations.
What is the load center of a 48 long pallet?
The load center of a pallet refers to the distance from the front of the pallet to the center of gravity of the load it carries. For a standard 48-inch long pallet, the load center is typically considered to be 24 inches if the load is evenly distributed across the entire length of the pallet. However, if the load is uneven or concentrated in a specific area, the load center may vary accordingly. It's crucial to know the load center for safe handling and stability during transport.
How much quantity nutmeg can load in 20 feet container?
how many tons nutmeg ABCD load in 20 feet container
Where is the load centered if the distance from the handle to the wheel axle is 4 feet?
Assuming the load is evenly distributed from the wheel to the handle, it would be 2 feet. But if it is a wheelbarrow, there is more load over the wheel than load at the handle end when lifted, so my estimate would be 1.5 feet from the wheel.
What size steel I beam do I need to span 32 feet with a load of 2500LB at center?
What size steel I beam do I need to span a 32 feet garage with a floored storage above and no posts
What size beam will span 18 feet?
That question cannot be answered without knowing the load on the beam.
How does point loading affect beam sizing versus uniform loading with point load in center of beam?
The moment of a beam is twice that for central load vs uniform load for a simple support beam; hence it needs twice the section modulus for sizing; for fixed ends the moment is 50% higher for central load vs uniform load
What are loads on a beam?
It all depends on the dimensions of the steel beam
What size of beam will span 18 feet with a load of 2130psi?
That depends on many other factors. What is the beam material? Is the load a point load concentrated in one spot, or is it uniform across the total span? Specing beams is something that should be left up to a qualified person.
What happens when a load is applied to the beam?
when the load is applied in the beam then deflection takes place. the nature of the deflection depends on the support provided on it
What size laminated timber beam is needed for a 23 foot clear span under a 15 foot roof in between load bearing walls?
38 feet longIt is not possible to give a definite answer without more detail. The construction and type of roof will determine the load (weight) bearing on the beam, and factors such as wind load and earthquake load, and the way the roof bears on the beam (truss/point load/distributed load) will all affect the sizing.
What size laminated timber beam is needed for a 23 foot clear span under a 15 foot roof in between load bearing walls -?
38 feet longIt is not possible to give a definite answer without more detail. The construction and type of roof will determine the load (weight) bearing on the beam, and factors such as wind load and earthquake load, and the way the roof bears on the beam (truss/point load/distributed load) will all affect the sizing.
To remove 8 feet of load bearing wall and replace with steel beam what size beam?
With a span of only 8" you can probably use a wood beam, but without a set of plans no one can accurately answer your question.
What is the maximum span for a 2x6 beam?
The maximum span for a 2x6 beam is typically around 10-15 feet, depending on the load it needs to support and the building codes in place.
What actually happens when load is applied to the beam and why does this condition occur?
the beam gets bend if the load is more then the resisting force of the beam and if the resisting force is more then the load it doesn't bends.
What is formula for maximum load due to bending of a simply supported beam?
The strength, S, of the beam is Mc/I where M = max moment to fail = PL/4 for load concentrated in the middle of the beam or WL/8 for uniformly distributed load. Here P is the concentrated load, W = distributed load, c = distance to outer fiber from neutral axis and I the area moment of inertia of the beam. L = length Solving for load maximum, P = 4IS/Lc for concentrated center load W = 8IS/Lc for distributed load
