answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: What the function pushbutton?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Does a 1987 Chevy half ton 4x4 have a shifter for 4wd or a pushbutton?

shifter


How do you reset the engine light?

With the engine off, press and hold the odometer reset pushbutton. Start the car. Keep finger on odometer reset pushbutton until "oil life" message starts flashing. Release the button.


How to Set a radio sation in a 2005 envoy?

1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1 or XM2. 3. Tune in the desired station. 4. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the station that was set will return for that pushbutton. 5. Repeat the steps for each pushbutton.


1987 Scottsdale how to bypass ignition switch with pushbutton Which wires do I need to tie in to?

orange and pink


How do you change the combination on kwikset powerbolt?

1. Remove Plastic cover on interior side of lock 2. Press Black Pushbutton one time 3. Enter User Code on keypad 4. Press Lock Button on keypad 5. Press Black Pushbutton one time


How do you reset the change oil light in a 2003 Oldsmobile alero?

Listed in your owner's manual. However, the reset pushbutton performs two functions. The first function is to find or select the change oil light. The second function is to reset the change oil light. So, when the manual says press the reset pushbutton, it means to press and release, press and release, press and release, ... and so on.... until the change oil light is selected. The change oil light is selected when it begins to flash on and off. Once the change oil light is selected by it flashing on and off, press and hold the reset pushbutton again in solidly to actually reset the light. Hold the reset pushbutton in until the chimes sound. This confirms the change oil light is reset and the light should go out.*Remember* before you even begin resetting using the reset button, the car must be in neutral or park or it will not work.AnswerIf you do not have an oil change reset button located on the drivers side inside the fuse panel. Turn ignition key to the on position (with engine off). Depress accelerator pedal 3 times. Oil change light should blink and you should here a beep, light will go out. Turn ignition key off.


Where is the ignition on a Corvette?

The new ones do not have one. You get a fob that you carry in your pocket, and it sends a signal to the car, so everything works by pushbutton.


How do you turn off the tire warning light in a Highlander?

At the very bottom of the dashboard just to the left of the steering wheel there is a pushbutton - after making sure your tires are propery inflated, INCLUDING THE SPARE TIRE, turn on the ignition and depress the pushbutton and hold for 5-10 seconds. This should re-set the low tire pressure warning light.


How many appliances have microchips?

I can't count that high. Those that have a digital readout or pushbutton switches most likely have a controller processor microchip


Can you put a Chevy 383 engine with a 1964 Dodge Dart pushbutton transmission?

No, not unless summit racing makes a special adapter plate to do it.


How do you get the front left rotor off a 1992 F150 4x4 with pushbutton 4x4?

take off the wheel, take off the caliper, pull


How would you connect a mini momentary pushbutton switch and a 12VDC backup buzzer using only one 9 volt battery?

Simply connect all three items in series. When the pushbutton switch is momentarily depressed, current flows in the loop. Since the 'power supply' is 25% short of the buzzer's rated operating voltage, the buzzer may or may not sound.