0
What else can I help you with?
What is the Line drawn at the bottom of a column of numbers?
It is used to indicate the end of a block of numbers or can be used to indicate that the number below the line is the sum of the numbers above it.
Where in drawing a center line is used?
In a drawing, a centre line is used to show the centre of a part.
In the scale used on a blueprint 14 of an inches represents 2 feet. On the blueprint what is the length of a room with an actual length of 20 feet?
To find the length of the room on the blueprint, we can set up a proportion based on the scale provided. Since 14 inches on the blueprint represents 2 feet in reality, we can calculate the blueprint length for 20 feet using the ratio: [ \text{Blueprint length} = \frac{14 \text{ inches}}{2 \text{ feet}} \times 20 \text{ feet} = 140 \text{ inches}. ] Therefore, the length of the room on the blueprint would be 140 inches.
A blueprint for a house shows a bedroom being 5. 5 inches wide The scale used to create the blueprint is 0.50 in equals 1 ft What is the actual width of the bedroom?
11 feet
Why are the absolute value symbols used when indicating the length of a line segment?
Because line segment lengths are often calculated as a square root, the absolute value symbols indicate it is only the positive solution that counts, as a distance cannot be negative.
What does a ditto line on a blueprint look like?
it is a series of repeated double-dashes ( -- -- -- -- -- ) used to indicate a repeated detail.
What is a leader line in engineering drawing?
A leader line is a thin line on a design or blueprint that is used to connect a dimension line with a particular area or point on the drawing.
Indicate the center of a two-way road used for two-way traffic?
A two lane roadway usually has a yellow dotted line down the center separating traffic lanes. When the line changes to a solid line, it means "No Passing". If the solid line is to the right of center then that lane has a "No Passing" restriction. When there is a double yellow line, there is "No Passing" in either direction.
What type of line is normally used in a mechanical drawing or blueprint to represent an edge or object not visible to the viewer?
Medium solid line
What does ns mean on a blueprint?
"NS" on a blueprint typically stands for "not specified" or "not shown." It is used to indicate that a specific detail or dimension is not provided on that particular drawing and may need to be clarified or determined through other means.
What is the Line drawn at the bottom of a column of numbers?
It is used to indicate the end of a block of numbers or can be used to indicate that the number below the line is the sum of the numbers above it.
What is a center line for drafting?
what a center line is, is a line in the center used for drafting thanks for the question i really had a good time looking up for you.
How do you use blueprint in a sentence?
A blueprint is technically a drafting diagram for mechanisms or architecture. But it is used metaphorically to indicate a detailed plan of specific actions to complete a task. Example : "The contractor received three sets of blueprints for the building." Example : ""The general's career path was a blueprint for junior officers seeking promotion."
Where in drawing a center line is used?
In a drawing, a centre line is used to show the centre of a part.
What did neumes 4 line staff f c or g clef mean/show?
Neumes are symbols used in medieval music notation to indicate the pitch and rhythm of a piece of music. The four-line staff, also known as the Gregorian staff, was a later development in musical notation that provided a more precise way of representing pitch. The "F" clef and the "C" clef are both used to indicate the position of specific notes on the staff. The "F" clef is used to indicate the position of the note F on the staff, while the "C" clef can be placed on any line to indicate the position of the note C. The "G" clef is also used to indicate the position of specific notes on the staff, with the center of the clef curling around the line that represents the note G. The "G" clef is also used to indicate the position of specific notes on the staff, with the center of the clef curling around the line that represents the note G.In summary, the four-line staff and the "F", "C", and "G" clefs provide a way for composers and musicians to accurately notate and perform music, with each clef used to indicate the position of specific notes on the staff. If this answer helped you, consider visiting and subscribing to my new YouTube Channel TheQuickFactShow. I would be grateful.
What is arrowhead'?
arrowheads are used to indicate the end of a dimension line or leader
What type of symbol is used to indicate a major heading?
A blank line before the major heading and a blank line after the heading is an indicator on the document as the heading. And the number signs used to indicate numbers are dots.
