0
When you start measuring from a point other than zero on the ruler what must you do to the measurement obtained?
Wiki User
∙ 8y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the definition of measurement of an angle?
A complete rotation of a ray around a point is 360 degrees or pi radians. That defines the two common units of measuring angles. The measurement of an angle is the number of such units between the two rays which form the angle.
What is the measurement from one point to another point?
A line
Where is the measuring point for longitude?
The Prime Meridian.
What is the measurement of a radius?
"Radius" is a measurement that refers to a circle. It's the distance from the circle's center to any point on its curve.
What is the difference between datum dimensioning and chain dimensioning?
Datum dimensioning is where a single reference point is used for all dimensions in a single direction. E.g. If Point A is declared the reference point, then Points B, C, D, etc, will all be measured relative to Point A, not to each other. Chain dimensioning is where each point is measured to the next. E.g. Point B is measured from Point A, Point C is measured from Point B, Point C is measured from Point B, and so on. The problem with chain dimensioning is that each measurement relies on the accuracy of the previous measurement. If there is a tolerance associated with each measurement (+/- X), then the tolerance for each subsequent dimension accumulates and becomes the number of measurements times the tolerance of each measurement (+/- n*X). Since datum dimensioning uses only one reference point, the tolerances cannot accumulate as each measurement is isolated, rather than relying on the accuracy of the previous measurement. Common practice is to only use datum dimensioning in design drawings to ensure greater accuracy over the entire design without requiring tighter tolerances.
What measuring business cycle activity what is the trend?
The 0 point from which the measurement begins. A+ Class
How do you read the correct measurement from the measuring apparatus?
To read the correct measurement from a measuring apparatus, ensure that your eye is at the same level as the measuring line on the apparatus. Read the measurement at the bottom of the meniscus for liquids in a graduated cylinder, or at the exact point where the measurement aligns with the scale for other types of measuring tools like rulers or tape measures. Record the measurement with the appropriate units.
What is the trend in measuring business cycles?
The 0 point from which the measurement begins. A+ Class
What unit is used in measuring type and fonts?
The unit of measurement is called "point". 72 points = 1 inch.
When measuring one point to another what are you measuring?
When measuring one point to another point you are measuring distance.
To properly record a measurements you must record which of the followingg?
The starting point, the ending point, and the measurement used to measure in between.
What is a measurment standard defined as?
In science, measurement is the process of obtaining the magnitude of a quantity, such as length or mass, relative to a unit of measurement, such as a meter or a kilogram. A measurement answers the general question, "how many?", as in how manymiles, or millimeters, or gigahertz. As measurement is basically about counting, measurement is conducted in numbers and is quantitative, in comparison to other observations which may be made in words and are qualitative. The term measurement can also be used to refer to a specific result obtained from the measurement process.
What are the advantages and disadvantages of 3 point micrometer and 2 point micrometer?
Advantages of 3-point micrometer: improved accuracy and reduced measurement error due to additional contact points, suitable for measuring non-round parts. Disadvantages: more complicated setup and calibration, higher cost compared to 2-point micrometers. Advantages of 2-point micrometer: simpler setup and operation, lower cost compared to 3-point micrometers. Disadvantages: may have decreased accuracy and increased measurement error compared to 3-point micrometers, limited suitability for measuring non-round parts.
What is the definition of measurement of an angle?
A complete rotation of a ray around a point is 360 degrees or pi radians. That defines the two common units of measuring angles. The measurement of an angle is the number of such units between the two rays which form the angle.
What do you use to measure small amounts?
small measurements That depends on what you are measuring. For mass, you may want to use an analytical balance. For volume, a buret or Eppendorf pipette would be useful. Like I said before, it is highly dependent on what your measuring and what the point of the measurement is.
When measuring motion the starting point is called the?
When measuring motion, the starting point is referred to as the "initial position" or "reference point." This helps establish a baseline for measuring distance or displacement.
How do you find the volume of a plastic pen?
get a beaker or measuring cup of water and fill it to an even point and record it. then put the pen in the water and record new measurement of water. subtract the new measurement from the old one and you have the volume of the pen! :)
