0
It depends on the type of ruler you are using. Depends if you are using a just metric unit ruler or if you are using a yard/meter stick. The measurements should be written along the edge of the ruler.
What else can I help you with?
Where is 1.83 inches on a ruler?
1-7/8 inches
What does .30 inches look like on RULER?
On a ruler, .30 inches is slightly less than one-third of an inch. It can be found by measuring just a bit beyond the quarter-inch mark (0.25 inches) and before the half-inch mark (0.5 inches). If your ruler has 1/16 or 1/32 inch markings, .30 inches would be between the 5/8 inch and 3/8 inch marks. It may be helpful to use a decimal ruler or a ruler with finer increments for precise measurement.
Where is 0.166 inches on a ruler?
To find 0.166 inches on a ruler, locate the 1/8-inch mark, which is 0.125 inches. Then, estimate a little less than halfway between the 1/8-inch mark and the 1/4-inch mark (0.25 inches). The 0.166 inches is slightly closer to the 1/8-inch mark than to the 1/4-inch mark.
Where on a ruler is 8.8 inches?
To locate 8.8 inches on a ruler, first find the 8-inch mark, which is typically the eighth tick mark on a standard inch ruler. Then, count 8 small divisions past the 8-inch mark, as each inch is usually divided into 16 smaller increments. Since 0.8 inches is equivalent to 8/10 of an inch, it will be slightly less than the halfway point between the 8 and 9-inch marks.
What does 3.60 inches look like on a ruler?
It's between 9/16 and 5/8
Where is 1.83 inches on a ruler?
1-7/8 inches
Where is two thirds on a ruler?
On a 12 inch ruler, the 1/3 point would be 12/3, or at 4 inches.
What does .30 inches look like on RULER?
On a ruler, .30 inches is slightly less than one-third of an inch. It can be found by measuring just a bit beyond the quarter-inch mark (0.25 inches) and before the half-inch mark (0.5 inches). If your ruler has 1/16 or 1/32 inch markings, .30 inches would be between the 5/8 inch and 3/8 inch marks. It may be helpful to use a decimal ruler or a ruler with finer increments for precise measurement.
where is .71 inches on the ruler?
Where is 0.71 inches on the ruler
Where is 0.166 inches on a ruler?
To find 0.166 inches on a ruler, locate the 1/8-inch mark, which is 0.125 inches. Then, estimate a little less than halfway between the 1/8-inch mark and the 1/4-inch mark (0.25 inches). The 0.166 inches is slightly closer to the 1/8-inch mark than to the 1/4-inch mark.
Where on a ruler is 8.8 inches?
To locate 8.8 inches on a ruler, first find the 8-inch mark, which is typically the eighth tick mark on a standard inch ruler. Then, count 8 small divisions past the 8-inch mark, as each inch is usually divided into 16 smaller increments. Since 0.8 inches is equivalent to 8/10 of an inch, it will be slightly less than the halfway point between the 8 and 9-inch marks.
What does 3.60 inches look like on a ruler?
It's between 9/16 and 5/8
What is 3.166667 inches on a ruler?
3.166667 inches is 3.166667 inches, whether on a ruler or anywhere else.
What does 45 of a inch look like on a ruler?
On a standard ruler, 45 inches would be represented as 3 feet and 9 inches, since there are 12 inches in a foot. You would find the 3-foot mark and then count an additional 9 inches from there. If you are specifically looking for the fractional part, 45/8 inches would be 5.625 inches, which is slightly over 5 and a half inches, or just under 6 inches on a ruler.
What is 6.1 on a ruler?
a little over 6 1/8 inches, unless it's a 10ths ruler it may mot have a mark to indicate tenths
What 2.95 inches on a ruler?
On a ruler, 2.95 inches would be located between the 2-inch mark and the 3-inch mark. This measurement is typically represented by smaller incremental markings between the whole numbers on the ruler. Each inch on a standard ruler is divided into 16 equal parts, so 2.95 inches would fall 15 parts past the 2-inch mark.
Where is 1.666 on a inch ruler?
On an inch ruler, 1.666 inches would fall between the 1 5/8 inch mark (1.625 inches) and the 1 11/16 inch mark (1.6875 inches). To locate 1.666 inches precisely, you would need to estimate the position between these two marks based on the incremental markings on the ruler.
