answersLogoWhite

0

What else can I help you with?

Related Questions

Two measurements are used to rate the capacity of a UPS?

ohms and watts


What two measurements are use to rate the capacity of ups?

VA and Watts


Is ups input or output device?

UPS is Uninterruptable Power Supply. It is neither input not output. It supplies electrical power to a computer when the main electrical supply is interrupted. It does not handle data in any way.


What will be input and output current of 10 KVA 3 phase UPS?

A 10 KVA 3-phase UPS will have an input and output current that depends on the specific voltage of the system. You can calculate the current by dividing the apparent power (in this case 10 KVA) by the square root of 3 multiplied by the voltage. For example, for a 208V system, the input and output current would be approximately 28.8 amps.


What are the best practices for selecting a 240V UPS system for a commercial facility?

When selecting a 240V UPS system for a commercial facility, consider the following best practices: Determine the power requirements of your equipment to ensure the UPS system can handle the load. Choose a UPS system with sufficient capacity to support your critical equipment during power outages. Look for a UPS system with features like surge protection, voltage regulation, and battery backup to ensure reliable power supply. Consider the physical size and installation requirements of the UPS system to ensure it fits in your facility. Evaluate the reputation and reliability of the UPS manufacturer to ensure long-term performance and support.


How many batteries required to run 2 ton ac through ups?

No way to give you a simple answer- will depend on the storage capacity of the batteries, and the efficency of the inverter in the UPS unit, and the efficency of the AC unit. That is a 24,000 BTU air conditioner, with a large current draw- typically 3200-3500 watts. It will also depend on how LONG you will want to run the AC system on battery- it is not for an indefinite time.


What is the amps of a 650 VA UPS?

To answer this question the voltage of the UPS has to be stated. Take that voltage and divide it into the 650 rating. The answer will be the output amperage of the UPS.


Are AC and DC kilowatt hours different for determining size of an UPS?

Kilowatt-hours is kilowatt-hours, regardless of AC or DC. However, UPS's are rated in kilowatts, not kilowatt-hours. If you are talking about battery capacity versus output power, its still different, but in that case you need to consider the efficiency of the UPS. You also need to consider run-time limitations on the UPS, if there happen to be any.


How can you calculate the capacity of the UPS you need for your home entertainment system?

The most easiest way is to get yourself a little device that measures the compsumption of power by the set. When you know what it uses, take that amount and add 10%-15% to it. That will be the capacity of the ups you will need. Keep in mind though that a ups is ment to provide power for a limited amount of time during a power failure.


What the use of computer UPS?

A computer UPS (Uninterruptible Power Supply) is designed to provide power to a computer system if normal power fails. The length of time a UPS will support a computer depends on the capacity of the UPS and the draw of the system being supported. Properly configured and installed, most systems will monitor the UPS and begin a normal shutdown when notified by the UPS that a power outage is in process. Some are large enough to maintain computer operations long enough for backup power generation to come online.


Two measuremnets to rate capacity of UPS?

1) Rated Protection of the UPS 2) Run Time. Rated protection is usually in KVA or VA (KilliVolt amps for very large UPS or Volt Amps for smaller UPS). This is because UPS typically have multiple outputs like 120V 240V and possibly 12VDC. Some only list WATTS. This assumes the UPS will have only one Voltage output so the Volts X Amps=Watts was already calculated. There is also something called a "Power Factor" that comes in to play. For computers it is ~60% which means if you are backing up a PC it will take more power than you think or the UPS will run for less time than you think because of the power factor. Runtime is usually presented in a chart since it will vary based on the load it is supporting. A battery has a rated Amp/Hour capacity. Amps per hour. You use a fraction of this over time until there is no more energy. Using Ohms Law you can determine the Amps from Watts or KVA/VA. P=IxE or Power ( watts) = Current( amps) x Electrical energy ( Volts) So I (amps) = P(watts) / E ( volts) . There are other factors like the battery charge level, ambient temperature and losses in cabling etc, that affect the run time in amp hours.


How do you calculate the load percentage of a three phase UPS?

output power/Rated power