answersLogoWhite

0

What else can I help you with?

Continue Learning about Math & Arithmetic

What is line standard and end standard?

line measurement- distance between two lines end measurement- distance between two faces


What would be the best measurement to find the length of a grasshopper?

The best measurement to find the length of a grasshopper would be to use a ruler or caliper. Measure from the tip of its head to the end of its abdomen, ensuring that the grasshopper is straightened out for an accurate reading. This measurement should be taken in centimeters or millimeters for precision. It's important to handle the grasshopper gently to avoid stress or injury.


What are end to centre measurement of 6 no 10 victaulic 90 elbow?

The end-to-center measurement for a 6-inch, Schedule 10 Victaulic 90-degree elbow typically measures approximately 4 inches. This measurement is taken from the end of the pipe to the centerline of the elbow. However, it's important to refer to the manufacturer's specifications or installation guides for precise measurements, as they can vary slightly depending on the specific product design.


How do you measure on a tape measure?

To measure (for example) a 2 metre long plank of wood: Place the tang at one end of the plank, stretch out the tape along the plank's length, read off the measurement at the other end of the plank. In our example, the tape should read 2 metres.


What is estimated length?

An estimate is an approximate calculation or judgment of the value, number, quantity, or extent of something. Length is the measurement or extent of something from end to end.

Related Questions

Why should the experimenter avoid using the end of a meter stick when making a measurement?

The end of a meter stick is less precise due to potential wear and tear, leading to inaccuracies in measurement. Using the end can also introduce parallax error when aligning with a measurement scale. It is advisable to use the edge or the start of the scale for more accurate and consistent measurements.


What is line standard and end standard?

line measurement- distance between two lines end measurement- distance between two faces


When did the whole African Americans Should Be Treated Unfairly thing start and end?

started since time immemorial and has yet to end.


What word means end to end or on end?

The word is length. It means the measurement of something from end to end.


What is squerd centermiters a measyrement of?

To correct yourt English Grammar and Spelling. 'What is squared centimetres a measurement?' Or ' What measurement does square centimetres represent?' The preposition 'of' is NOT required, and should not be used at the end of a sentence. To answer your question. It is a measurement of area. A piece of paper would be measured in square centimetres.


What is meant by fitting allowance?

The fitting allowance is the difference: (pipe end to fitting center measurement) minus (pipe end to end measurement). It is the amount of length the fitting adds to the end of the pipe (to get the center of the turn).


If the retention rate in July is 90 percent what is the annualized percentage rate of retention?

Retention rate should not be annualized like turnover. Retention is based on specific individuals for a specific measurement period, i.e.Retention should being calculated as indicated below: # of Associates remaining Active at the end of the measurement period that were Active at the beginning of the measurement period/ # of Associates at the beginning of the measurement period. **The actual Associate that was employed as of the first day of the measurement period is taken into account not the number of hires that may have been termed during the measurement period.


Length is the measurement of?

Strictly speaking, the length of something is the distance between the two end points of it.


Why is it better to align the meterstick with edge of the object at the 1 cm mark rather than at the end of the stick?

Aligning the meterstick with the edge of the object at the 1 cm mark helps to reduce parallax error by ensuring the starting point is accurate. This method also allows for more precise measurements as the beginning of the scale is directly aligned with the object being measured, leading to more accurate readings.


Cubical units?

Using cubed.at the end of a measurement


When do you get your period when you have started the pill?

At the end of the three weeks of pills, there should also be a week of different colored pills, that's when you get it.


How do I know if a Ranger 410 shotgunis 3 inch or 2 and three quarter?

It should be stamped/marked on the side of the barrel-receiver end. If not, take it to a gunsmith for measurement.