0
What else can I help you with?
How do you calculate area of flange?
i want surface area m2 for flange 24 inch
What should 3 inch drain pipe drop per inch?
1/4 inch per foot.
What slope to use on sewer drain lines?
One eighth inch drop per foot of run.
Is possible for each are five inches long and you want to insert a ten inch diagonal is it possible explain?
No problem in a hexagon, for example.
Can you use a two inch pipe for a toilet drain?
Wouldn't recommend it as things may back up in the drain line. 4" line is the norm ... you want to get rid of waste, not keep it around longer.
How do you relocate a drain in a concrete slab?
Change how? Move the location, you bust out the concrete and move it. Replace or repair the flange that the toilet hooks to. Cut the existing flange off flush with the floor and install a new repair flange. They can be brass or steel. You can use a PVC one that fits in the drain and seal it with a wax ring under it and screw it to the floor. If you are working with cast iron flange and the slots where the bolts are supposed to go is broken out, they make a repair piece for this. It is a 3/4 inch wide by 3-4 inch long crescent shape piece that slides under the flange and the bolt that holds the toilet fits into it. You may have to chip out a little concrete along the edge to get these under the flange.
How do you remove the broken closet flange from a cast iron drain pipe?
I removed the broken flange by perforating the lead filling between the drain pipe and the flange - i.e., drilling holes every 1/4-1/2 inch or so with a regular drill and then sawing through the filling with a power saber saw. Then pried the flange off with a pry bar. Wasn't as bad as I expected. - Dan
How do you calculate area of flange?
i want surface area m2 for flange 24 inch
How do you install a regular toilet flange on a cast iron 6 inch sewer pipe?
If you can get to the 6 inch cast iron, you could use a rubber coupler between the cast and the flange. If it is in the concrete, put a piece of 4 inch PVC inside the 6 inch and lead it in like you would a regular cast joint. Leave the 4 inch above the floor and slide the flange over it, screw it down and cut the 4 inch flush with the flange. They make just the flange that will slide over the pipe.
How far from the wall does a toilet drain go in the floor?
12-13 inches to the center of the drain.... make sure your drain pipe is 1/4 inch drop per foot. also use the sweeping y drain if possible. leave lots of room for the flange. mount the toilet after the floor is in.
How do you raise the level of the toilet after tile install?
Depends on how much you need. Sometimes you can just use two wax rings. If that doesn't do it, you can use a PVC toilet flange and use it to make up the difference. Cut it off the right height and use a wax ring between it and the old flange. You cut the old flange out and extend the pipe and a new flange. If you put backer board down first and then the tile, you probably raised the floor level about 3/4 of an inch. Two wax rings with the black funnel insert in them should be enough to seal the toilet to the drain.
Can a toilet be installed where you currently have a sink?
the sink drain is prob.in the wall.you would have to get a wall mount commode,or install drain in floor and plug drain in wallAnswerYou also need a 3 or 4 inch drainpipe.Ans 3 - You can do this if you fit a new 3" drain to the main pipe and run it to a toilet flange where the sink is.
Will the toilet install properly if the flange is higher than tile?
Depends on how much higher and how the toilet is made. They are not all the same. A PVC flange is supposed to be above the floor level and will clear. They are about 1/4 inch thick. You can probably get away with up to 3/8 of an inch, but any more than that and the toilet will rock on the drain and eventually leak.
What are the benefits of using a 3 inch offset toilet flange in a bathroom renovation project?
A 3-inch offset toilet flange can help in a bathroom renovation project by allowing the toilet to be properly positioned over the existing drain pipe without the need for major adjustments. This can save time and effort during installation and ensure a secure and leak-free connection.
What is the recommended height for a toilet flange to be installed above the floor?
The recommended height for a toilet flange to be installed above the floor is typically around 1/4 inch to 1/2 inch.
How do you move a toilet 3 inches with concrete sub-floor?
If the extisting drain is lead pipe it can be moved about an inch and the use a offset brass floor flange and lead wipe it in place that will give you the 3" you want
How do you move a toilet 3 inches with concrete sub floor?
If the extisting drain is lead pipe it can be moved about an inch and the use a offset brass floor flange and lead wipe it in place that will give you the 3" you want
