answersLogoWhite

0

What else can I help you with?

Continue Learning about Math & Arithmetic

What do the numbers on a tact switch mean?

The numbers on a tact switch can mean a variety of things. Typically, the number will be a model or part number. Depending on where the number is, that will tell what the number is for. You can call the manufacturer and ask them specifically for your switch.


What is the advantage of having the binary number system to represent data inside the computer instead of the decimal number system?

They use the binary sysem because the number 1 means the switch is turned on and the number 0 means the switch is off. There is no way to use the decimal number system.


What is the highest hexidecimal number from a 10-position dip switch?

A 10-position dip switch can represent binary values ranging from 0000000000 (0 in decimal) to 1111111111 (which is 1023 in decimal). The highest hexadecimal number from this binary representation is obtained by converting 1111111111 to hexadecimal, which results in 3FF. Therefore, the highest hexadecimal number from a 10-position dip switch is 3FF.


When the numerator and denominator switch such that the product of a number and its reciprocal is 1?

Unless the first number is zero, then this must ALWAYS be the case.


What does the check 4wd light mean?

Your 4WD is currently not working. There has been some problems with late model GM trucks 4WD. Some are related to the pushbutton switch on the dash. My 02 silverado was warrantied by dealer because of a bad dash switch. This just happened to me. I was told to check the fuse first, if it wasn't blown it would be in the switch. Sure enough the fuse was blown...replaced and now working fine. same thing happened to my 03 silverado 2500hd. its the 4wd actuator switch. i think there is a bulletin on this.

Related Questions

Is Nintendo NX the Switch?

Yes, the codename prior to the official announcement of the Switch was the Nintendo NX


When port security is used on a switch which violation mode will cause an snmp trap to be sent and traffic to be dropped when the number of secure MAC address for a port is reached?

Port security is used on a switch and the number of secure MAC addresses for a port is reached, the violation mode that will typically cause an SNMP trap to be sent and traffic to be dropped is the "Shutdown" or "Protect" violation mode.


Why did the driver window switch stop working when the passenger switch on the drivers side is still working?

Maybe its your driver-side window regulator that stopped working.


What does it mean when you call a boost number and it says all circuits are busy please try your call again later announcement 8 switch 113 dash 5?

When you hear the message "all circuits are busy, please try your call again later" followed by "announcement 8 switch 113 dash 5," it means that the telephone network is currently experiencing high traffic and cannot connect your call at that moment. This could be due to a large number of incoming calls or technical issues with the network. The specific announcement code helps technicians identify the type of issue affecting the call routing. You may need to wait and try your call again later.


How can you tell if your convertible top switch is bad?

top stops working. you stop hearing the buzzing sound of the switch working.


1970 Chevrolet high speed blower switch not working?

replace the switch.


Why is your temp gauge not working?

i change the thermostat and the temp switch but still not working


Why is my AC switch not working properly?

Your AC switch may not be working properly due to a faulty connection, a malfunctioning switch, or an issue with the electrical system. It is recommended to have a professional inspect and repair the switch to ensure proper functioning of your air conditioning system.


A c not working on 1998 Ford Taurus?

air conditioner not working on off switch


How do I reset the Sony car CD player?

my player panel switch & voice switch is not working


Why is your microwave working when you open it?

The door switch is faulty.


How do you fix AU 1999 falcon sedan stop light switch that is not working?

You need a flashlight and pliers. Crawl under the dashboard. On top of the brake pedal you see the switch and the push rod. Remove the yellow clip. Slide the switch sideways, the brake switch comes off. Look where the plastic spacers are before you remove the switch. Unplug the switch Ford part number for the switch is E73B-13480-AA