0
Can a 742 Woodmaster be disassembled and reassembled using common tools if at all?
It all depends on how far you want to go with disassembly. The trigger group can be removed by pushing the two pins out that maintain the trigger guard in the receiver with a flat-faced punch. The forearm can be removed by backing out the screw located in the very front of the forearm. The stock can be removed by removing the butt-plate/recoil pad and then inserting a screwdriver into the rear face of the stock and backing out the bolt holding the stock in place. If you are looking into removing the barrel to get at the receiver internal parts, a special wrench is recommended to prevent damage to the action bars. There is a small pin that maintains the bolt handle in place in the bolt carrier, so this pin will need to be drifted out to remove the bolt handle. The special wrench is needed to back off the barrel nut so that the barrel can be removed out the front of the receiver. Once the barrel has been removed the bolt, etc. can be removed out the front of the receiver. The special wrench can be purchased from Brownell's Inc. (on the web) that will cost around $40.00 or so. There are quite a few small parts involved with the bolt assembly so if one of these parts is lost or broken they will be difficult to replace as the Model 742 is no longer in production and parts have become very scarce. Good disassembly instructions are helpful. Go to http://www.krausebooks.com/category/firearms_knives
and buy the Gun Digest book Assembly/Disassembly for centerfire sporting rifles. The 742 is in there.
Add your answer:
Earn +20 pts
What are the basic tools and instruments used in electronics?
The most common electronic hand tool is an electric drill, which can be used to put holes into an object (usually wood) and can also be used to drive screws into a substance, or to pull them out.
What tools did Comanche use?
they used bow and arrow ,lance, shield ,and hunting knives and they also wove the fur into a rope. The tail even became a fly swatter!!
Is collective noun for tools is bag?
The collective noun for tools are a set of tools or a kit of tools. However, collective nouns are an informal part of language. Any noun that suits the situation can be used, for example, a bag of tools.
What are the release dates for Cool Tools - 2007 Cutting Tools - 9.7?
Cool Tools - 2007 Cutting Tools - 9.7 was released on: USA: 2011 USA: 25 November 2011
Where can you buy budget tools?
If one is looking for tools that are not too expensive, check out stores such as Canadian Tire, which has tools on sale often. Also check out a site such as Amazon.
Is the word tools a proper noun?
No- "tools" is a common noun.
What features of air tools pneumatic tools such as impact wrench air tools sanders pneumatic tools drivers should you notice when you buy them?
As one specialist of air tools, pneumatic tools, for examples: impact wrench, air tools sanders, pneumatic tools rivet nut tools....you should understand applications where you will use the air tools, pneumatic tools. If you need the air tools pneumatic tools for industrial or professional grades, you should first get them disassembled, then look thru the key components, such as blades, bearings to make sure they can bear daily Min. 8 hours continuous operation in heavy duty cycle.
What are common tools in Romania?
The same tools as in the other countries around the world.
What is traditional tools?
tools like a hammer, screw driver, saw, tape measurer. (Tools that are very common.)
What tools do you need to remove the battery from a 2005 harley sporster?
Common hand tools.
What tools do you need to remove a starter for 94 Oldsmobile achieva?
Common hand tools.
How do you change the water pump on a 2004 Chrysler pt cruiser and can it be done without experience?
The entire passenger side of the engine needs disassembled. It requires a few special tools. I would not recommend an inexperienced person attempting it.
What air force to covers common hand tools?
32-1-101 use and care of hand tools and measuring tools
What tools are needed to replace alternator on 2002 Hyundai Sonata?
Common metric hand tools.
What are some common tools usually used to do defect tracking?
Some common tools used in defect tracking include Aardvark, Bug Monitor and GNATS. Some of these tools are freeware while others cost money. You can get more information about these tools at their respective websites.
Are there special tools required to change the fuel pump in a 99 montaro sport?
No, no special tools needed, just common hand tools.
What are the most common tools used by jewelers?
There are multiple tools used by jewelers. The most used tools vary depending on the need of the customers.
