0
More information is needed to answer this question. There are too many variables:
* How much compressed air do you have available (volume - cfm)? * What type of blast system are you using to blast? Siphon? Pressure? * What size blast nozzle will you be using? * What size/type of abrasive* will you be using?
* Hopefully you will not be using silica sand. The health hazards (silicosis) associated with breathing in the dust generated in the blasting process is not worth the cost savings or convenience in using that abrasive. Dust masks, air fed hoods or air fed helmets help a little bit but DO NOT 100% protect the person blasting.
What else can I help you with?
How do Bakugan open?
Bukugan Battle Brawlers are action figure warriors, that are tucked into spheres that pop open when they're rolled onto a metallic game card or metal surface.
Why would a metal shack be an unsafe home in the desert .?
Because the sun in the desert would burn the metalThe metal surface would constantly absorb the sun's heat - making it impossible to live in !
In call of duty modern warfare 2 what is a bullet penetration kill?
A bullet penetration kill is when you kill someone through a surface such as , a wall,or metal. (Note: The only way of accomplishing this is if you have FMJ or Full Metal jackets on) Have a Great day,Night,afternoon,or whatever
Can you powder coat over zintec metal plate?
Yes, you can powder coat over zintec metal plates, which are typically coated with a zinc-rich layer to provide corrosion resistance. However, it’s essential to ensure that the surface is properly prepared by cleaning and removing any contaminants or oils. Additionally, a suitable primer may be required for optimal adhesion of the powder coat to the zintec surface. Always consult the powder coating manufacturer's guidelines for the best results.
Was the Titanic made of metal or wood?
She was made of metal... lots and lots of metal.
How do you sandblast metal a oil drill rig?
To sandblast metal on an oil drill rig, first ensure the area is well-ventilated and take necessary safety precautions, including wearing protective gear. Use a sandblasting machine equipped with an appropriate abrasive material, such as silica sand or aluminum oxide, and adjust the pressure settings to suit the metal surface being treated. Direct the sandblast nozzle at an angle to effectively remove rust, paint, and contaminants while avoiding damage to the underlying metal. After sandblasting, clean the surface thoroughly to remove any remaining abrasive particles before applying protective coatings.
How do you sandblast paint from a toy tractor?
I use a small sandblaster with glass beads. Wear cotton gloves while blasting. It keeps body oil from contaminating the metal and besides---if you happen to sandblast your fingers it doesn't hurt quite as bad.
Can one fix Troy-accessory-Rack on metal surface?
Yes, this accessory rack can me affixed to any stable surface. It weighs 86 pounds.
How do you paint a walk in cooler?
First off, you will not want to paint the inside of your walk-in due to food safety issues. To paint the outside you will need to either sandblast the metal or use a self etching primer. Normal paint will run on a smooth metal surface so you need to give the paint places to cling to. And with painting a walk-in there is a good chance the paint will not properly adhere, so be prepared to repaint or deal with chipping.
Does taping an electrical wire to a surface ground the current?
That would depend on the surface: wood surface - noplastic surface - noungrounded metal surface - nogrounded metal surface - yesetc.
What exactly is case hardening?
Case hardening, also referred to as surface hardening is the process of hardening a surface of a metal. It is done by surfacing the metal surface with a layer of metal on top of it, in order to harden it.
What is the surface metal raceway trade name?
One common trade name for surface metal raceway is "Wiremold".
How can I effectively sandblast bike frames for optimal results?
To effectively sandblast bike frames for optimal results, follow these steps: Ensure the bike frame is clean and free of any dirt or grease. Use a sandblasting machine with the appropriate abrasive material for metal surfaces. Wear protective gear such as goggles and a mask to prevent inhalation of dust particles. Sandblast the bike frame evenly and at a consistent distance to avoid uneven surfaces. After sandblasting, clean the frame thoroughly to remove any remaining abrasive material. Apply a primer and paint to protect the frame from rust and corrosion.
Does metal lath require furring?
No. The metal lath replaces the wood furring.
IS 100 pounds metal and 100 pounds cotton equal?
If it weights 100 pounds then it weighs 100 pounds no matter what it is made of.
Why it feels sticky when touching a cold metal surface?
When you touch a cold metal surface, moisture in the air can condense on the surface, creating a thin layer of water. This water can make the metal feel sticky when you touch it because your skin can't easily glide over the wet surface. The sensation of stickiness is due to the interaction between your skin, the water, and the metal surface.
How many pounds of metal did the titanic have on it?
1billon
