What kind of question is that. What resistors, what circuit are you talking about?
The speed of a wave = (frequency) x (wavelength) = 2.5 meters per second.
CLASS -C amplifier is having high ditortion due to which they are not used in audio frequency work
Groups of eight notes are known as octaves. This series of eight notes occupy the interval between, and including, two notes, one having twice or half the frequency of vibration of the other.
Resonance is caused by the transfer of sound from a single system to another storage mode. This is generally considered complete when the vibration frequency of each area is matched in frequency.
Rihanna isn't having a baby.
Resistors have resisting power(resists the electric power).Due to having the resistive property, the name resistor is given to such electrical device.
The frequency of an RC phase shift oscillator is determined by the values of the resistors and capacitors in the feedback network. It is typically calculated using the formula f = 1 / (2 * pi * R * C * sqrt(6)), where f is the frequency in hertz, R is the resistance in ohms, and C is the capacitance in farads.
jumper
f=P*N/120 f=Frequency in Hz P= No. of Poles N=Rotor Speed in Revolution per minute(rpm) for P=4 and N=3600, f comes out to be 120 Hz. So frequency of voltage produced is 120 Hz. But this is not practical. Generally 4-Pole generator has N=1500rpm(for 50 Hz) or 1800rpm for 60 Hz. Two pole generator can have N=3600rpm(f=60Hz). The most practical situation is generator having N=3600Hz with 2 Poles. Hope It will be helpful!!!
I'm no expert but I believe the high frequency is due to the number of poles (North-South) of the pilot exciter. The frequency of a generator is directly link to its speed and the number of poles. Most generators will run at 1800RPM and will have 4 poles to achieve 60Hz. The pilot exciter being on the same shaft will also run at 1800 rpm but will probably have more then two poles. finding the formula for frequency of a generator should help you in answering your question. The next question should be why would you build a pilot exciter with multiple poles and a high frequency? The output of the pilot exciter is going to be rectified to DC so it would make sense to do it with a high frequency and get a smoother DC signal out of the rectifier.
Diesel generator are generator that uses diesel. having the ability to withstand corrosive particles in fuel(diesel).
In this case, the frequency of a wave emitted by one person would increase (be perceived as having a higher frequency) by the other.In this case, the frequency of a wave emitted by one person would increase (be perceived as having a higher frequency) by the other.In this case, the frequency of a wave emitted by one person would increase (be perceived as having a higher frequency) by the other.In this case, the frequency of a wave emitted by one person would increase (be perceived as having a higher frequency) by the other.
pitch. A higher frequency sound will be perceived as having a higher pitch, whereas a lower frequency sound will be perceived as having a lower pitch.
There are multiple benefits or having a backup power generator. Some of them are: you get a higher home value, cheaper insurance, you can have power when the main goes off.
Having a diesel generator for emergencies is a great idea. There is a great selection at www.dieselserviceandsupply.com .
As I have no information on the circuit I can make no valid predictions as to the effect of replacing diodes with resistors. However I assume the effect(s) will resemble that of having very defective diodes in the circuit.
A signal generator generates either audio or RF frequencies (depending on the capabilities and designed purpose of the generator) for testing other electronics equipment. Makes it easier to make tests on a device without having to have it "in circuit". It's a lot easier to test a piece of equipment on a work bench rather than trying to test it in place.A function generator supplies TTL (transistor to transistor) square wave pulses, sine and sawtooth wave forms for various testing purposes. It's a lot easier to work on something on the work bench and being able to remove a circuit board and just supply power and a signal saves having to take a whole piece of equipment into the shop. Then again, you also can use an oscilloscope for troubleshooting when you jave a good, known signal to work with. That applies to both types of generators.A: A function generator is just like a signal generator except it generates a function like a ladder step or unusual increases or decreases in voltage to generate a required function