0
By asking this question you are probably not quite ready to take on this particular task. You may or may not get lucky and receive some information in an answer here! If you hope to get enough information on this site to be able to do this job properly and safely, please do not rely on getting accurate information about such a potentially dangerous subject. Really, don't do this one yourself. Electricity is far too dangerous to handle if you have not been trained how to do this work. If you put just one wire in the wrong place you risk being killed by electrocution or you could even start a house fire.
How to do this job depends entirely on the Wiring Codes or Regulations for the locality (Town/State) and on the exact locations of some of the outlets you wish to install. If they are anywhere subject to water splashes or spray - such as in any room supplied with running water pipes, like a kitchen, bathroom, shower room, etc., or in a pool-side area - in many places nowadays it is actually illegal to attempt to do this kind of work unless you are already a licensed electrician. If you don't want to go to your local library or bookstore - to find and read some books about electrical wiring and appliances and how to install them safely, and to find out about your local Wiring Codes and Regulations - then the best advice anyone should give to you is to call a licensed electrician either to do the job for you or to advise you what you may be allowed to do yourself. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS. If you do this work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicator
to insure the circuit is, in fact, de-energized.
What else can I help you with?
Can I add a circuit breaker wired in parrell to a current breaker to reduce the load on the breaker?
No, add new breaker,find a junction box and split the series, or add a box and split the load. You only need to do this if the breaker is tripping from overload. 12ga wire should have a 20amp breaker not a 15amp. If I understand your question,wired in parallel, this would be one hot connected to two breakers, first off two breakers is 220v not 120v , and 220v has two hot wires. Never connect two breakers together on one line.
How do I get 220 volt circuit?
If you need a 220v circuit at only 15 or 20 amps: Get a new breaker to replace your 110v single pole breaker with a 220v double pole breaker. (You cannot exceed the original breaker's amperage rating unless you also replace the wire with a larger size). Shut off the panel's main breaker (the wires coming into the main breaker will remain hot, so don't touch them.) Remove the old 110v circuit's neutral (white) from the neutral bus bar in your distribution panel. Remove the old 110v circuit's hot (black) from the old 110v breaker. Remove the old 110v breaker. Install the new 220v breaker in place of the old breaker. (This may require you to rearrange some breakers if the old breaker was in between others) Reconnect the black wire to one terminal of the 220v breaker, and reconnect the white wire to the other terminal. Turn on the main breaker, and your new 220v breaker. Before you do this, be sure where the actual circuit goes. Changing 110v to 220v if the circuit is feeding regular 110v receptacles will cause damage to devices plugged into them. Be sure you remove all 110v devices (receptacles) from the circuit before converting it. If you need a 220v circuit for a dryer or other large appliance, your existing wiring will not be sufficient to do the above. You will need to install a new breaker and wiring. For this task, you should consult a professional electrician.
Can 110V circuit with 2 wire size of 10 and a ground be converted to 220V after changing the outlet and breaker?
No, changing the outlet and breaker does not change the voltage of the circuit. To convert a 110V circuit to 220V, you would need to rewire it with proper gauge wire rated for 220V and install a compatible 220V outlet and breaker. It is important to consult with a licensed electrician for this type of conversion to ensure safety and compliance with electrical codes.
What size wire and circuit breaker is needed for an electric oven 4 wires with rated load of 34.9 amps 220v that is about 100 foot run from the electrical panel?
That would be a 40 amp 220v circuit. Circuit breaker is 40 amps and wire is 8 awg. Should use solid copper wire. Follow oven installation instructions.
Why do you convert 120v circuits to 220v circuits?
You would need to change a circuits voltage if your adding a load that requires 220 when the present circuit supplies 120. If you need to do so it's pretty simple! First purchase a double pole breaker at the proper amp rating. Next find the breaker in the panel that supplies power to the circuit you wish to change to 220. Turn off the breaker and pull it out. Find the neutral for that circuit. Then double check and make sure it's the right neutral. Then check one more time. Now take the neutral and the hot wire for that circuit and connect them to the double pole breaker. install the breaker into the panel and turn it on. If you connected the right neutral you'll have 220 on that circuit. If you didn't you'll know because you'll trip the breaker.
Can I add a circuit breaker wired in parrell to a current breaker to reduce the load on the breaker?
No, add new breaker,find a junction box and split the series, or add a box and split the load. You only need to do this if the breaker is tripping from overload. 12ga wire should have a 20amp breaker not a 15amp. If I understand your question,wired in parallel, this would be one hot connected to two breakers, first off two breakers is 220v not 120v , and 220v has two hot wires. Never connect two breakers together on one line.
How do I get 220 volt circuit?
If you need a 220v circuit at only 15 or 20 amps: Get a new breaker to replace your 110v single pole breaker with a 220v double pole breaker. (You cannot exceed the original breaker's amperage rating unless you also replace the wire with a larger size). Shut off the panel's main breaker (the wires coming into the main breaker will remain hot, so don't touch them.) Remove the old 110v circuit's neutral (white) from the neutral bus bar in your distribution panel. Remove the old 110v circuit's hot (black) from the old 110v breaker. Remove the old 110v breaker. Install the new 220v breaker in place of the old breaker. (This may require you to rearrange some breakers if the old breaker was in between others) Reconnect the black wire to one terminal of the 220v breaker, and reconnect the white wire to the other terminal. Turn on the main breaker, and your new 220v breaker. Before you do this, be sure where the actual circuit goes. Changing 110v to 220v if the circuit is feeding regular 110v receptacles will cause damage to devices plugged into them. Be sure you remove all 110v devices (receptacles) from the circuit before converting it. If you need a 220v circuit for a dryer or other large appliance, your existing wiring will not be sufficient to do the above. You will need to install a new breaker and wiring. For this task, you should consult a professional electrician.
Can 110V circuit with 2 wire size of 10 and a ground be converted to 220V after changing the outlet and breaker?
No, changing the outlet and breaker does not change the voltage of the circuit. To convert a 110V circuit to 220V, you would need to rewire it with proper gauge wire rated for 220V and install a compatible 220V outlet and breaker. It is important to consult with a licensed electrician for this type of conversion to ensure safety and compliance with electrical codes.
What size wire and circuit breaker is needed for an electric oven 4 wires with rated load of 34.9 amps 220v that is about 100 foot run from the electrical panel?
That would be a 40 amp 220v circuit. Circuit breaker is 40 amps and wire is 8 awg. Should use solid copper wire. Follow oven installation instructions.
Why do you convert 120v circuits to 220v circuits?
You would need to change a circuits voltage if your adding a load that requires 220 when the present circuit supplies 120. If you need to do so it's pretty simple! First purchase a double pole breaker at the proper amp rating. Next find the breaker in the panel that supplies power to the circuit you wish to change to 220. Turn off the breaker and pull it out. Find the neutral for that circuit. Then double check and make sure it's the right neutral. Then check one more time. Now take the neutral and the hot wire for that circuit and connect them to the double pole breaker. install the breaker into the panel and turn it on. If you connected the right neutral you'll have 220 on that circuit. If you didn't you'll know because you'll trip the breaker.
Can a 2-pole circuit breaker be used for 110V 220V or 440V?
All three, on 110V a split receptacle, on 220V a baseboard heater, on 440V a construction heater or similar resistive load.
Can you wire two 220V devices off of one 50A GFCI breaker where the total load is 38A?
No, only one GFCI per circuit.
What happens when both 110v leads are applied to one side of a 220v electric motor?
The breaker will blow because you are effectively causing a short circuit.
How can I get 220v at home?
To get 220v at home, you will need to install a 220v outlet or have an electrician upgrade your electrical system to accommodate the higher voltage. This typically involves installing a double-pole circuit breaker and wiring that can handle the increased voltage. It is important to consult with a professional electrician to ensure the safety and proper installation of the 220v power source in your home.
Can you use a 40amp breaker on your 220v welder with 12-3 wire?
No, it is not safe to use a 40-amp breaker on a 220V welder with 12-3 wire. The wire size should match the breaker size to prevent overheating and potential fire hazards. In this case, a 30-amp breaker should be used with 12-3 wire for a 220V welder.
In wiring for 220v can one use 2 15a breakers instead of a ganged 30a breaker?
No, when wiring for 220v, you should use a ganged 30A breaker to ensure safe and proper functioning of the circuit. Using two 15A breakers is not recommended as they may not trip simultaneously in an overload situation, potentially causing damage to the circuit or appliances.
What voltage feeds the coil on a shunt trip breaker?
220V
