yes, but you will overwork your compresser and you will have to change your txv
No, it is not recommended to pair a 5 ton coil and furnace with a 3 ton compressor. The sizes need to be compatible for the system to operate efficiently and effectively. Mismatched components can lead to performance issues and potential damage to the system.
Bond's Work Index is typically expressed in kilowatt-hours per ton (kWh/ton). It represents the energy required to reduce a material from infinite size to 80% passing a specific screen size in a grinding circuit.
Yes, you can replace a 3.5 ton condenser with a 4 ton condenser as long as the existing system can accommodate the higher capacity. It's important to ensure that the new condenser is compatible with the existing components, including the evaporator coil and air handler, to maintain the system's efficiency and performance. We recommend consulting with a professional HVAC technician to ensure a proper fit and installation.
There is no direct conversion between ton and horsepower since they measure different things. Ton measures weight or mass, while horsepower measures power or work rate. However, if you are referring to metric ton (tonne), you can use a formula to convert it to a unit such as kilowatts, which is a measure of power like horsepower.
A ton of rocks and a ton of water both weigh the same, which is one ton. Weight is determined by the mass of an object, regardless of its composition.
The term "gross ton" can refer to either a long ton or a metric ton, both of which are larger than a short ton. A long ton is equivalent to 2,240 pounds, while a metric ton is equivalent to 1,000 kilograms.
not very well. a 4 ton system needs about 1600 cfm to provide it's full capacity of cooling. a 3 ton furnace puts out about 1200 cfm. in addition, the evap coil typically attached to the furnace needs to match the tonnage of the outdoor unit. so, the evap coil must be 4 tons. If you currently have a 3 ton furnace and evap coil, the system will not work, and you will most likely ruin the compressor in the outdoor unit.
You may be able to turn up the blower speed but you will probably still not get the appropriate cfm. You may be able to swap out the blower but you may run into problems with fitting the new one in place or the proper sizing of the return and supply duct work.
Yes it will. Typically a coil is sized a 1/2 ton larger than the a/c out side for efficiency, but a whole ton bigger should still work
It is not recommended to mix a 2 ton coil with a 2.5 ton compressor as it may lead to inefficiencies and potential system failures. It is best to match the coil and compressor sizes to ensure optimal performance and efficiency of the HVAC system.
Yes it will. Typically a coil is sized a 1/2 ton larger than the a/c out side for efficiency, but a whole ton bigger should still work
Usually a 3 ton - 70,000btu furnace.
No easy answer with the information given. You might be able to increase the blower speed but that probable wont get you enough air anyways. You might be able change the blower depending on your furnace. Depending on the evaporator coil 3 or 5 ton you either wont remove the proper amount of moisture from the air(the biggest part of what makes you feel cool) or there will not be enough air blowing over the coil and it will freeze up. Technically could put a freeze switch to turn of the condenser. Most likely you will wear out the condenser quicker then it should.
Yes, it is recommended to use a 4 ton coil with a 4 ton AC unit to ensure optimal performance and efficiency. Using a mismatched coil size can lead to issues such as poor cooling, increased energy consumption, and reduced system lifespan.
Maybe. The coil is not matched to a 2 or 3 ton truck It is matched to the engine and igniton control system. So it may be the same part #.
I'm not an air conditioning expert, but I would expect that the compressor will run a lot more than it needs to. A 2 ton coil will not cool as much air as a larger capacity 3 ton coil. Experts?
It is not recommended to pair a 3-ton coil with a 3.5-ton condenser. Mismatched components can lead to decreased efficiency, poor performance, and potentially even damage to the system. It is best to use matching components for optimal operation.
Between $490-765. That's a range for a 2 ton to 5 ton residential a/c coil cleaning.