0
No, it is not safe or recommended to connect a 200 amp service to a 125 amp panel. The panel must be rated to match the amperage of the service to avoid overloading the panel and potential fire hazards. It is important to upgrade the panel to match the service amperage.
Add your answer:
Earn +20 pts
Should a 2 AWG copper wire be used to feed a 125 amp sub panel located 125 feet from main panel?
No, the conductor is too small. The feeder to a 120/240 volt sub panel should be a 1/0 copper or a 2/0 aluminium conductor. This size conductor will limit the voltage drop to 3% or less when supplying 125 amps for 125 feet on a 240 volt system. ACWU 90 (Armoured Cable Wet location Underground 90 degree C). ACWU 90 cable is code approved for direct burial and is used in many projects as an underground service distribution feeder. Aluminium is much cheaper than copper for this type of installation.
Would a 125 amp service panel be enough for a 1900 square foot house?
A 125 amp service panel should be sufficient for a 1900 square foot house, as long as the electrical load of the house is within the panel's capacity. It's important to consider factors like the number of appliances, lighting, and other electrical devices in the house to ensure the panel can handle the demand. Consulting with a licensed electrician can provide a more accurate assessment for your specific situation.
Where is the neutral bus bar in a stab-lok panel BE116-32 125 amp.?
The neutral bus bar in a Stab-Lok panel BE116-32 125 amp is typically located on the side or at the bottom of the panel box. It is a metal bar with multiple screw terminals for connecting the neutral wires from branch circuits. Refer to the panel's installation manual or contact a qualified electrician for specific guidance on locating and working with the neutral bus bar.
How many 50 amp breakers feeding 50 amp outlets can you install from a 125 amp main panel?
You can install a maximum of two 50 amp breakers feeding 50 amp outlets from a 125 amp main panel. Each 50 amp breaker is using half of the available amperage from the main panel.
How can you find out the bus bar rating in a panel that is old and the rating sticker has fallen off is it safe to say that a panel with a 100 amp main breaker has a bus rated AT 125 AMPS?
A 100 amp panel should have a conservatively rated busbar and wiring but this says nothing about your particular panel. If you are asking a question relating to safety it needs to be seen by an electrician.
How many amps can be put on a 125 amp service?
You should not load a 125 amp panel any more than 100 amps.
Can you swap out your 125 amp panel for a 200 amp panel?
You can but you may need new Service wires ran to your house to support the larger load. You will probably be looking at paying a couple thousand dollars for it.
What is the maximum amperage capacity of the 125 amp main breaker in this electrical panel?
The maximum amperage capacity of the 125 amp main breaker in the electrical panel is 125 amps.
Fuse panel layout 1999 E150?
Check out www . motorcraft service . com ( no spaces ) Click on Owner Guides The owners manual ( including the fuse panel diagram ) can be viewed on-line ( the fuses and relays section starts on page 125 )
What are the key features and specifications of the Siemens 125 amp panel?
The Siemens 125 amp panel is a electrical distribution panel that can handle up to 125 amps of electricity. It typically has a main breaker or main lug, multiple circuit breakers for individual circuits, and is designed for residential or light commercial use. It is important to consult the specific model's specifications for exact details on features and dimensions.
What is the recommended size for the main breaker in a residential electrical panel, specifically for a 125 amp main breaker?
The recommended size for a main breaker in a residential electrical panel with a 125 amp main breaker is typically 150 amps.
What are the key features and specifications of the Square D 125 amp panel?
The Square D 125 amp panel is a type of electrical panel that can handle up to 125 amps of electricity. It typically has a main breaker or main lug, along with multiple circuit breaker slots for individual circuits. The panel is designed to safely distribute electricity throughout a building, with features such as overload protection and grounding capabilities. It is important to consult the manufacturer's specifications for specific details on the panel's dimensions, materials, and installation requirements.
What are the specifications for a 125 amp outdoor panel?
A 125 amp outdoor panel typically has a voltage rating of 120/240 volts, with a maximum continuous current capacity of 125 amps. It is designed to be weatherproof and suitable for outdoor installation, providing power distribution for various electrical circuits in outdoor settings.
Should a 2 AWG copper wire be used to feed a 125 amp sub panel located 125 feet from main panel?
No, the conductor is too small. The feeder to a 120/240 volt sub panel should be a 1/0 copper or a 2/0 aluminium conductor. This size conductor will limit the voltage drop to 3% or less when supplying 125 amps for 125 feet on a 240 volt system. ACWU 90 (Armoured Cable Wet location Underground 90 degree C). ACWU 90 cable is code approved for direct burial and is used in many projects as an underground service distribution feeder. Aluminium is much cheaper than copper for this type of installation.
Would a 125 amp service panel be enough for a 1900 square foot house?
A 125 amp service panel should be sufficient for a 1900 square foot house, as long as the electrical load of the house is within the panel's capacity. It's important to consider factors like the number of appliances, lighting, and other electrical devices in the house to ensure the panel can handle the demand. Consulting with a licensed electrician can provide a more accurate assessment for your specific situation.
What is the recommended wiring diagram for a 125 amp sub panel installation?
The recommended wiring diagram for a 125 amp sub panel installation typically involves using a 2-pole breaker in the main panel, running 4 wires (2 hot, 1 neutral, 1 ground) from the main panel to the sub panel, and connecting them to the corresponding terminals in the sub panel. It is important to follow local electrical codes and consult a professional electrician for proper installation.
What are the specifications of the 125 amp Square D panel?
The 125 amp Square D panel has a maximum current capacity of 125 amps, suitable for powering medium-sized electrical systems. It typically includes circuit breakers, bus bars, and grounding provisions to ensure safe and efficient distribution of electricity within a building.
