You connect the fuse to the live wire as it is the one with the potential difference of 220V and in case of short circuit current will blow out here
Wiki User
∙ 15y agoA fuse is typically connected to the live wire in a circuit. This is done to protect the circuit from an overload or short circuit, as the fuse will blow or trip and cut off the current flow if there is an issue.
Wiki User
∙ 14y agoLive wire is called a hot wire, as this is the wire that gives the current.
Earth wire is a ground wire. So one is hot, and one is ground.
Wiki User
∙ 15y agoLive.
So that the live wire is isolated when the fuse blows. If a fuse was placed in the neutral, the equipment would still be live when the fuse blows.
The live wire is connected to the fuse to ensure that the circuit is interrupted in case of an overcurrent or short circuit, which helps prevent fires and electrical hazards. The neutral wire completes the circuit and does not carry any current in normal circumstances, so connecting it to the fuse would not offer the same protection.
To wire two bulbs to one switch, connect the live wire from the switch to the live terminal of the first bulb. Then connect a wire from the live terminal of the first bulb to the live terminal of the second bulb. Finally, connect the neutral wire from the switch to the neutral terminals of both bulbs. This setup will allow the switch to control both bulbs simultaneously.
If you connect the main power from two live wires instead of a live wire and a neutral wire, it can lead to a short circuit in the electrical system. This can cause damage to your appliances, risk of electric shock, and could potentially start a fire. It is important to always connect electrical wires properly to ensure safety.
The live wire is the wire that carries electrical current to the light fixture, while the neutral wire provides a return path for the current to complete the circuit. In a ceiling light, the live wire is typically colored black or red, while the neutral wire is colored white or gray. It is important to properly identify and connect these wires to ensure safe operation of the light fixture.
prepare to fry
So that the live wire is isolated when the fuse blows. If a fuse was placed in the neutral, the equipment would still be live when the fuse blows.
The live wire is connected to the fuse to ensure that the circuit is interrupted in case of an overcurrent or short circuit, which helps prevent fires and electrical hazards. The neutral wire completes the circuit and does not carry any current in normal circumstances, so connecting it to the fuse would not offer the same protection.
The neutral wire and power wire are never connected together.
The neutral wire in a fuse box is typically colored white or gray to indicate that it carries the return current from the electrical circuit back to the service panel. It is important to consult local electrical codes and standards, as wire colors can vary by region.
Connect to the circuit neutral wire which should also be white.
If there is no ground wire connect the ground wire to the neutral wire.
The color of a wire does not necessarily determine if it is live or not. It is always best to use a voltage tester to check if a wire is live before working on it, regardless of its color. Remember to always follow proper safety precautions when dealing with electrical work.
In Bangladesh, the live wire is typically red, brown, or black; the neutral wire is typically blue or black; and the ground wire is typically green or green with a yellow stripe. It is important to consult with a local electrician or electric code regulations for accurate information.
Connecting a live wire to ground can cause a short circuit. This can lead to a sudden surge of electricity flowing through the circuit and may result in a tripped circuit breaker or blown fuse, as well as potential damage to electrical equipment and a risk of fire. It can also pose a serious shock hazard to anyone in contact with the grounded object.
Red goes to a switched live i.e one that is only live when the ignition is switched on. Yellow goes to a permanent live i.e one that is always live whether the ignition is n or not, like the cigarette lighter, and maintains the station configuration memory. However, a modern car should have a pre-wired Din connector and a local motor factor will have the corresponding universal adaptor for your radio; connect colour ro colour (inc speaker wires) and plug it in !
The colour red designates that the wire is used as a live wire. The neutral wire is identified as white in colour.