0
Do you need a separate switch for a sensor light if I am connecting it from an existing light outside?
If you are taking the power from the existing light outside you have to be aware that when that outside light is switched off then the sensor light will not work. Your best choice should be power the sensor light from an un-switched source. This could be an existing receptacle outlet in a nearby location. Check your sensor configuration to see if the device has the function to be locked on and off by interrupting the voltage supply to it. If it does then a switch in its circuit is mandatory to make this function work. If this function is not included in the device then just connect it as the instructions explain and the fixture will come on when it senses movement and go off after a timed interval.
What else can I help you with?
Sharp atomic clock SPC373 can not get your outside temp to set?
1st make sure your batteries are still working on the outside receiver. Then go inside and take the batteries out of your inside receiver (the clock). Put the new batteries in the clock and wait for the outside temperature to set. DO NOT SET THE TIME or anything else until the signal is received from the outside temp. If you get frustrated, take the outside transmitter inside and when it blinks the red light that is when the signal is sent, so wait for that. Hopefully this works for you.
Is there a replacement outside temp unit for a sharp atomic clock spc373?
Yes, you can replace the outside temperature unit for a Sharp Atomic Clock SPC373 with a compatible wireless outdoor temperature sensor. Look for sensors that operate on the same frequency as the clock and are designed for use with similar models. Ensure that the new sensor is capable of transmitting data to the clock for accurate temperature readings. Always check the manufacturer's specifications for compatibility before purchasing.
How do you replace a mercury vapor light sensor?
Most Mercury Vapor Lamp Fixtures have a PLUG IN module on top of the fixture. Most are about the size of an inverted "shot glass" and have a photocell "eye" somewhere on the outside surface. Typically, you turn the Module counterclockwise to "unlock" the module from the socket and pull the module UP and off the top of the lamp fixture. Failure mode for these Light Sensors are twofold: Either [ 1 ] the electric eye's lens gets cloudy and the light stays on unless it is VERY sunny....or [ 2 ] the Module, being mounted ABOVE the light fixture gets HOT...and over the years the module gets COOKED and fails. Take the light sensor with you to an electrical supply house and match it up with a new one !! BYW: Inspect the socket and plug of the Light Sensor module & lamp fixture. Often the "cooked module" will fail because of socket/plug failure. The plug/socket Phenolic materials break down from the heat over the years . Or the contacts corrode. NOTE: It is important , when installing the Light fixture...that the plug-in Light Sensor' photocell lens is pointing AWAY from the building or other mounting structure. If the "electric eye' is facing the structure..the reflected light will confuse the light sensor and the lamp will come on DIM[*] , flicker or turn off & on constantly. [ * ] Do not confuse the " comes on DIM " statement with the normal DIM warmup cycle of the lamp. It is also advised to have the High Output Merury Vapor LIght on a dedicated electrical circuit. If you are using an existing circuit for outside-the-house loads..... such things like pool pumps etc will extinguish the lamp when the pump kicks in.. The pump's heavy inductive load in-rush current on startup will cause the lamp to go out..... in a few minutes the lamp will restart, warm up and come back at full intensity.
How night switch can be made or what is the procedure to make a night switch?
A night switch can be made by installing a light sensor that detects low light levels, triggering the switch to turn on the lights. The procedure involves connecting the light sensor to the switch to control the power supply based on the ambient light levels. This allows the lights to automatically turn on at night and turn off during the day.
How do you wire two outside light sensing motion porch lights that are controlled from one switch with each light having a white black ground and optional red wire?
Connect the black wire from the switch to the black wires of both lights. Connect the white wires together. Connect the red wire, if used for the motion sensor, to the black wires on the lights. Connect all ground wires together and to the ground terminal on the switch. Make sure to turn off power before connecting any wires for safety.
Can a light sensor be wired into an existing light?
No
Where is 2003 outside temperature sensor?
Where is outside temperature sensor 2003 Monte Carlo SS
Where is thea outside temperature sensor on a 900se Saab?
Where is thea outside temperature sensor on a 900se saab?
Where is the outside temperature sensor on a Ford Freestyle?
where is the outside temp sensor located on a 2005 ford freestyle
Where is the outside air temperature sensor on a Subaru Forrester?
Where is the outside temp sensor on a subaru forester 2007
Where is outside temperature sensor located in opel omega 2003?
mine is opel omega 2002 3.2. i don't know exactly where the sensor is but i can guess. my car is left side drive and the battery is to the driver side. i made an accident and only damaged part of the left (driver side) bumper, left headlight and left floodlight. that is when i noticed that the outside temperature sensor stoped working. the sensor should be in the left side to get damaged by the accedent. when i checked the cable connecting the two (LH & RH) floodlights there were a third plug which was supposed to be connected to a device. i guess it was to the outside temperature sensor.
Where is the outside temperature sensor located on a 1999 Cadillac Deville?
where is the outside temp. sensor located on a 1997 cad.deville
Where is the IAT sensor for 1998 cavalier?
On a 1998 Cavalier, the IAT sensor is located in the hose connecting the air cleaner to the throttle body. The IAT is a two-wire sensor.
Where do you find the outside air sensor on 1998 Dodge Grand Caravan?
You will find the outside air temperature sensor under the battery tray
Where is the IAT sensor on a Vauxhall calibra?
The Intake Air Temperature sensor is either part of the Air flow sensor, or a separate sensor in the intake pipes not far from it.
Where is the map sensor on ef el falcon?
the map sensor is on the outside of the throttle body.
Where will you find the outside temp sensor on vectra 2002 model?
I've been told that the outside temperature sensor is located under the front bumper.
