No tandem breakers are of the same value.
No. The breaker must protect the circuit components such as wiring, outlets and switches that are connected to the breaker. Therefore if you have a 30 amp circuit as dictated by its components you need to protect it with a 30 amp or less breaker.
In the US a miniature circuit breaker, sold in a single unit, is about 15$, about the same as a regular breaker. If sold as a double unit, meaning two mini breakers installed into one housing, then it is about 25$.
The electrical terminology for this type of breaker is a tandem breaker. It is where two breakers circuits can be in the same one breaker slot in a distribution panel. On this type of breaker there will be two output for a circuit value of what ever the breaker is rated for.
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
You should first check to see if you are not overloading the outlets. If you are, just unplug something and reset the breaker. However, this is also a symptom of circuit breaker failure. In that case, replace it with the same amperage breaker of the same or compatible brand.
circuit breaker is break the electrical circuit .circuit gear is generator analyzer
... fuse.
Typically yes because that is what makes sense. However, the subpanel could have the same size breaker as long as the panel were rated for that amperage and the wire sizes were appropriate.
since circuit breaker consists of coils they get heated up when high current flows, when this happens the coil get energised and pull the moving contacts to open thus the circuit breaker opens when high current flows.
No. The breaker must protect the circuit components such as wiring, outlets and switches that are connected to the breaker. Therefore if you have a 30 amp circuit as dictated by its components you need to protect it with a 30 amp or less breaker.
its a circuit breaker... call the dealer for the parts # or just buy it from them ($40). Try a junk yard or craigslist f150 f250 and bronco about the same year are all the same i think.
yes it is the main breaker
It must be on the same circuit in your breaker box. They both need dedicated circuits for them.
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
In the US a miniature circuit breaker, sold in a single unit, is about 15$, about the same as a regular breaker. If sold as a double unit, meaning two mini breakers installed into one housing, then it is about 25$.
Yes, a circuit breaker will function the same if supply and loads are reversed. This is the way that some sub panels are fed instead of a main disconnect at the top of the distribution panel.
Yes, the rating of a 3 pole circuit breaker is the same for each conductor that is connected to it. A three pole breaker rated at 30 amps will have 3 #10 wires from it that connect to the load.