0
Add your answer:
Earn +20 pts
Can you replace a 13 amp 125 volt appliance cord with a 15 amp 125 volt cord?
Yes, no problem at all going to a larger ampacity of wire. Larger size wire yes, smaller size wire no.
What wire size do you need for a 3phase 90amp 60hz 220v?
Wire size is based on the amperage capacity of the service it is feeding. You tell me the service amps and I can tell you the wire size.
What size wire would you use for a 70KW 240 vac single phase generator?
For a 70kW 240V single phase generator, you would typically use a wire size of 3/0 AWG copper wire. This size wire is rated to handle the current carrying capacity required for a generator of that size to ensure safe and efficient operation. Be sure to consult with a professional electrician to confirm the correct wire size for your specific installation.
Size wire is needed to run a 125 amp panel?
For a 125 amp panel, you would typically use #1 AWG copper wire or #2 AWG aluminum wire for the main service entrance conductors. It's important to consult local electrical codes and a qualified electrician to ensure the correct wire size for your specific situation.
What size wire is needed to feed a 125 amp sub panel from a 200 amp panel less than 200 wire feet away?
For a 125 amp sub panel located less than 200 feet away from a 200 amp panel, you would typically use a 2 AWG copper wire or 1/0 AWG aluminum wire to safely carry the current load. It's important to follow local electrical codes and regulations when selecting the wire size.
What is the appropriate wire size for a 125 amp circuit using THHN wire?
For a 125 amp circuit using THHN wire, the appropriate wire size would be 1/0 AWG.
What information does the 125 amp wire size chart provide for electrical installations?
The 125 amp wire size chart provides information on the appropriate wire size to use for electrical installations that require a 125 amp capacity. It helps determine the correct gauge of wire to ensure safe and efficient electrical connections.
Can you replace a 13 amp 125 volt appliance cord with a 15 amp 125 volt cord?
Yes, no problem at all going to a larger ampacity of wire. Larger size wire yes, smaller size wire no.
What size aluminum wire to feed 125 Amps 220 volt a distance of 175' and what size ground?
A 3/0 aluminum conductor will limit the voltage drop to3% or less when supplying 125 amps for 175 feet on a 220 volt system. If the 125 amp load is a sub distribution panel that is not going to be fully loaded to 125 amps then using the exact connected load, which might be smaller than 125 amps will effect the wire sizing. The grounding conductor for that size distribution panel is #6 bare copper.
What wire size do you need for a 3phase 90amp 60hz 220v?
Wire size is based on the amperage capacity of the service it is feeding. You tell me the service amps and I can tell you the wire size.
What size of wire to handle 125 Amp?
AWG # 1/0 copper would normally be used.
What size wire would you use for a 70KW 240 vac single phase generator?
For a 70kW 240V single phase generator, you would typically use a wire size of 3/0 AWG copper wire. This size wire is rated to handle the current carrying capacity required for a generator of that size to ensure safe and efficient operation. Be sure to consult with a professional electrician to confirm the correct wire size for your specific installation.
What size wire do you need to run 200 ft of 125 amp?
This is a voltage drop question. To give an answer the voltage must be stated.
Size wire is needed to run a 125 amp panel?
For a 125 amp panel, you would typically use #1 AWG copper wire or #2 AWG aluminum wire for the main service entrance conductors. It's important to consult local electrical codes and a qualified electrician to ensure the correct wire size for your specific situation.
How many amps is 2 wire good for?
depends on its use. If its for residential service its good for 125 amps In commercial and industrial installations it's a bit more complicated but you end up at the same 125 amps.
How many amps is 2 gauge wire good for?
depends on its use. If its for residential service its good for 125 amps In commercial and industrial installations it's a bit more complicated but you end up at the same 125 amps.
How do you wire a Nema L5-30 plug?
An L5-30P is a two pole three wire grounding 30 amp, 125 volt plug . The neutral wire is connected to the W terminal, the ground wire to the G terminal and the hot wire to the only terminal that is left. The small blade/slot is neutral (white), the larger blade/slot is hot (black) and the notched blade/slot is ground (green).
