0
Add your answer:
Earn +20 pts
If a current get too big and melts a wire what is it called?
If a current gets too big and melts a wire, it is called an overload. This can happen if the amount of current flowing through the wire exceeds its rated capacity, causing it to overheat and melt. It is important to use properly rated wires and circuit breakers to prevent overloads.
How big of a single pole breaker can you put on 12-2 wire?
You can use a 20-amp single pole breaker for 12-2 wire. This is the standard size breaker for 12-gauge wire in residential applications.
Is 8 3 wire too big to hook up an electric dryer?
No, a 8/3 wire is suitable for hooking up an electric dryer. This wire size is typically used to handle the electrical load required by a dryer. Make sure to also use the correct outlet and breaker size rated for the wire.
How big of breaker do you use for 115 volt?
Depends on the wire size used in the circuit. If you use AWG # 14 wire you must use a 15 amp breaker. If it is wired with AWG # 12 wire then you use a 20 amp breaker. If a AWG # 10 wire is used then a 30 amp breaker is required. The breaker protects the wiring from overheating so you must use the proper size breaker for the wire used.
How Can you put a wire from your engine to the inside on a 2004?
You can route a wire from the engine to the interior by identifying a suitable entry point through the firewall, using a grommet if necessary to protect the wire from damage, and securing the wire along the existing wiring harness to prevent any interference with moving parts. It's important to ensure proper insulation and protection to avoid any short circuits or damage to the wire. Consulting a professional or referring to the vehicle's service manual may be helpful.
What wires go to Solenoid on 1969 Ford Mustang?
1 big wire to batt positive other big wire to starter, 1st smalll wire to ign switch 2nd small wire to ground.
Where is the fusible link 03 dodge diesel?
Its the big black wire coming off the battety going into a smaller wire that connects to the alternator. the big black cable connects to a wire 4x as small that wire is the fusible link.
What wires go to what post on a starter for a '93 Saturn dohc?
The big red wire and the orange or blue wire go on the big stud in the middle. The small purple wire goes on the smaller stud
How big is 6 gauge wire?
The size of the wire is stated by its gauge under American Wire Gauge. Six gauge wire is size 6 AWG.
How big is WWF?
Do you mean welded wire fabric?
Does Eminem watch big brother?
eminem watches the wire and obssesd and euntorage not big brother
Where does the fabric coated resistance wire attach inside the car if you are converting from points to a HEI system and need to replace resistance wire with 12 gauge stranded wire?
eliminate the resistor wire all together but you want to run a new larger 12 gauge wire into the same circuit , in order to do that you need to take the fuse box down inside the car and you will see where that resistor wire ties into a big wire in the fusebox, it comes from the ignition switch, you need to tie into that big wire with your 12 gauge wire that you have run from the HEI.
How big in mm does the hole on a charm have to be to fit a chamilia bracelet?
Wire is 3mm I have purchased glass beads with 6mm hole will they go on the wire?
What has the author Loren D Anderson written?
Loren D Anderson has written: 'Adjustable wire fences for facilitating big game movement' -- subject(s): Wildlife management, Big game animals, Wire fencing
What size are the speakers on the door of a 1997 Chevy cavalier z24?
4x6 ...On the new speakers the big wire connector is the positive (+) .....the left positive speaker wire is Tan.... The right Positive wire is Lt. Green
Is wire an example of a conductor?
It matters what kind of wire like a cell phone charger would not be a conductor but a wire made for braces would be a big conductor. Also anything metal is a positive conductor of electricity. :)
If a current get too big and melts a wire what is it called?
If a current gets too big and melts a wire, it is called an overload. This can happen if the amount of current flowing through the wire exceeds its rated capacity, causing it to overheat and melt. It is important to use properly rated wires and circuit breakers to prevent overloads.
