How do you change 120V volt lines to 240V?

Answer 1

On a pure 240V circuit, no. There is no neutral. On a 240/120V circuit, yes. You have the needed neutral. Tapping 120volts off an existing 240volt branch circuit with a neutral is possible but is not a proper method. It does not comply with most electrical codes.

Answer 2

for USA, Canada and countries running a 60 Hz power service.A service drop to a home is done with wire that is called triplex. This means that there are three wires twisted together that go from the service pole to the mast head on your home. This is called a three wire system. There are 2 hot legs and a neutral. The voltage between the hot leg (one) and the neutral is 120 Volts. The voltage between the hot leg (two) and the neutral is 120 Volts. The voltage between hot leg (one) and hot leg (two) is 240 volts. The single pole breaker is a safety device that connects to the (load, at 120 volts) and returns from the load back to the neutral. The load in most cases will be lights, plugs small appliances. The two pole breaker is a safety device that connects hot leg (one) to the (load, at 240 volts) and returns from the load back to the hot leg (two) at the two pole breaker. The loads in this case will be oven, range tops, hot water tank, clothes dryer, and in many homes baseboard heaters.

<<>>

In USA 240V comes into your home even though most of your equipment is 120V. I say most because your clothes dryer for one, if you have an electrically-heated one, most likely runs on 240V. The answer to your question is that 2 legs (power lines) come into your house. One leg is colored Black, the other is Red.

Each leg is 120V to common (ground). The voltage is AC (Alternating Current) so it is always going from +120V to -120V on each leg. But at opposite times, so that at some point in the cycle one leg is +120V while the other leg is -120V. And if you measure the voltage difference between +120V and -120V you get 240V.

The US wiring system works like this: to turn on your lights you switch into one leg, the current goes through your wiring to your lights and back to common. But your dryer switches into one leg and returns the current to the other leg. If you look in your breaker box you see breakers on both sides. Looking straight across, these breakers are on the same leg (L1). The next set down the panel are on the opposite leg (L2). Adjacent breakers all the way down the panel are on opposite legs. A two pole breaker spans these adjacent legs and that is how you arrive at 240 volts. Your dryer is connected to a two pole breaker that taps into both Black and Red legs.

<><><>

To accurately specify a voltage, you have to specify two points to measure, and the voltage is the difference between the two. If only one point is given it is usually implied that the second point is a grounded or 0 volt point. In the U.S., the three wires that enter most homes can be thought of as at +120V, -120V and 0V relative to ground. The 0V line is the "grounded" conductor, sometimes also called "neutral" and must be well connected to the earth where the wires enter the building (and no where else!) The +120 and -120 are actually different phases of an AC voltage wave. So by choosing which two points to connect to, a load can receive 120V or 240 V. Since there are two ways to get 120V, the breaker panel is usually set up to distribute the load between the two 120V phases.

<><><>

As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.

Before you do any work yourself,

on electrical circuits, equipment or appliances,

always use a test meter to ensure the circuit is, in fact, de-energized.

IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

.

Answer 3

Yes, it is done with a step up transformer. The transformer is sized by the load that is connected to the secondary side of the transformer. Smaller control size Transformers are rated in VA (volt amps) and larger transformers are rated in KVA (kilovolt amps). VA is derived from amps times volts.

Answer 4

To change 120V lines to 240V, you would need to install a step-up transformer. This transformer will increase the voltage from 120V to 240V. It's crucial to consult with a licensed electrician to ensure the conversion is done safely and in compliance with electrical codes.

Answer 5

A 240 volt breaker can be removed and replaced with 2 - 120 volt breakers.

The existing 240 volt breaker should not be used to supply 2 separate circuits.

Answer 6

In simple words, NO!!! On the first day of Electricity 101 they tell you if you do not know what you are doing, DON'T DO IT!!!

Answer 7

You DO use the old wire. You must not run new wire and outlets of proper load rating for the job. Doing anything else is dangerous.

Answer 8

A far as I know, you can't. If a wire is used in a 120v circuit, the wire itself is only rated up to 15 amps, therefore it can't carry a full load without tripping the breaker.

Answer 9

Absolutely NOT. The 240 outlet pin configuration would be different from the 120 volt pin configuration. They would physically not fit into each other.