answersLogoWhite

0

Yes an adapter can be made. You must keep in mind that the US generator's speed is set for 60 Hz generation. The frequency of a generator is governed by the RPM of the engine. If the generator has speed control on it, it will have to be turned down so that the frequency meter reads 50 Hz.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Natural Sciences

How do you jump wires off three way switch?

Like any other switch: you fasten a pigtail to the screw terminal and use wire nuts to connect all other wires to the other end of the pigtail. Why you would ever want to do that in a 3-way would be a head-scratcher for a different question.


How do you connect multiple lights to one switch starting at the light?

You put switch in series with the black supply wire and the black wire to the first light. Then connect black wire of first light to black wire of second light, black wire of second light to third light and so forth. Do the same with the white wires and ground wires.


How do you wire a two way switch one controls the outlet the other the outdoor light with a pigtail?

You need two separate switches. You can get two switches that are in the same form factor as a single switch (2 gang switch). You use one switch for the outlet and the other for the light. You switch the black wires which are "hot".


How do you connect old home wiring to new wiring without a pigtail connection-There is not enough slack in the old wiring to pigtail and use a connector?

If there is not enough slack to create a pigtail connection, you can use a junction box to extend the old wiring. Cut the old wire short, strip the insulation, and connect it to a new wire with a wire nut inside the junction box. Make sure to secure the junction box properly and follow all local electrical codes.


What are the dangers of pigtail surge protector?

Answer for USA, Canada and countries running a 60 Hz supply service.There are no dangers to using a pigtail surge protector. The installation of the protector must be done correctly though. The pigtails must not be installed on an existing circuit that has an existing load on it unless the breaker is approved for more than one circuit load on it. The protector must use a new two pole breaker with no additional load on it except the surge protector. This is the correct procedure to connect a pigtail surge protector to a distribution panel board.

Related Questions

What is a pigtail on a dc generator?

Pigtail is a device to protect the brush from sparking


How do you properly connect wires using a wire nut with pigtail?

To properly connect wires using a wire nut with pigtail, strip the insulation off the wires, twist them together, and then twist on the wire nut securely. Finally, attach the pigtail wire to the wire nut to create a secure and reliable connection.


What is the purpose of a receptacle pigtail in electrical wiring?

A receptacle pigtail in electrical wiring is used to connect multiple wires together and then connect them to a single terminal on a receptacle. This helps to ensure a secure and reliable electrical connection, as well as to prevent overloading the receptacle.


How to pigtail an outlet for electrical wiring?

To pigtail an outlet for electrical wiring, first turn off the power to the outlet. Then, strip the wires and twist them together with a wire nut. Connect the pigtail wire to the outlet and secure it with a screw. Finally, attach the outlet back to the electrical box and turn the power back on to test the connection.


How can I properly install a pigtail for a dryer?

To properly install a pigtail for a dryer, first turn off the power to the dryer. Then, remove the old pigtail by disconnecting the wires and unscrewing it. Next, connect the new pigtail wires to the corresponding terminals on the dryer, following the manufacturer's instructions. Finally, secure the connections with wire nuts and tighten any screws. Turn the power back on and test the dryer to ensure it is working properly.


What is a sentence with the word pigtail?

Her hair had a pigtail at the back.


How do you properly connect and secure pigtail wires when installing a new electrical outlet?

To properly connect and secure pigtail wires when installing a new electrical outlet, strip the insulation off the wires, twist them together with a wire nut, and then wrap the connection with electrical tape for added security. Make sure the wires are securely connected and there are no exposed wires.


What is the purpose of an outlet pigtail in electrical wiring?

An outlet pigtail in electrical wiring is used to connect multiple wires together and provide a secure connection to the outlet. This helps to ensure a reliable flow of electricity and prevent loose connections that could lead to electrical hazards.


What are the necessary steps to install a pigtail receptacle in a residential electrical system?

To install a pigtail receptacle in a residential electrical system, follow these steps: Turn off the power to the circuit at the breaker box. Remove the existing receptacle and disconnect the wires. Connect the new pigtail receptacle to the wires, matching the colors. Secure the receptacle to the electrical box. Turn the power back on and test the receptacle to ensure it is working properly.


How do you jump wires off three way switch?

Like any other switch: you fasten a pigtail to the screw terminal and use wire nuts to connect all other wires to the other end of the pigtail. Why you would ever want to do that in a 3-way would be a head-scratcher for a different question.


What are the ratings and certificates for The Clue of the Pigtail - 1923?

The Clue of the Pigtail - 1923 is rated/received certificates of: UK:A


Is pigtail a compound word?

Yes, "pigtail" is a compound word made up of "pig" and "tail."