Shut off the power to the light circuit. Remove the old light switch if there is one. Remove the old lamp holder base. Make a diagram and note how the wires were attached, what colour screws to what colour wire. At the light switch wire nut the two wires that came off of the switch together. The switch plate cover will have to be replaced with a blank cover plate to cover the old switch box. Install the new pull chain lamp holder using the notes and diagram that you made. Some of the lamp holders that have a switch in them will not have terminal screws. The wire to the switch will be the "hot" wire. The other wire from the old lamp holder will be the neutral which should be a white wire. Insert the bulb and turn the power back on. Now the pull chain will control the light rather that the wall switch.
To convert a standard light fixture into a pull-chain one, you will need to replace the existing switch with a pull-chain switch. First, turn off the power to the fixture. Then, remove the existing switch and connect the wires to the new pull-chain switch following the manufacturer's instructions. Install the new switch into the fixture and secure it in place before turning the power back on.
If you've never done electrical work before, then you should do this with somebody else who has, as a safety precaution.
First you need to secure (turn off, and mark it so it will not be accidentally turned back on) the power to your circuit at the breaker. Test to make sure it is off. Next, install a light receptacle with a pull chain, and then turn the power back on. With the switch in the 'on' position, test that the chain works as desired. Next, secure power again, then using wire nuts, bypass the wall switch. Then you may remove the wall switch and replace with a blank, if desired.
To convert a swivel recessed light to accept a pendant light kit, you will need to remove the existing recessed light fixture and install a pendant light fixture in its place. This typically involves disconnecting the wiring for the recessed light and attaching it to the pendant light fixture according to the manufacturer's instructions. You may also need to install a mounting bracket to support the pendant light fixture.
No, the fixtures do not have anything is common other that emitting light. If you are talking about removing the fluorescent fixture and installing a new fixture that can take a LED lamp then the answer is yes.
No, a dimmer pack will not convert the voltage. It simply controls the amount of power (voltage) sent to the light fixture, allowing you to adjust the brightness. You need to ensure that the dimmer pack is compatible with the voltage of the light fixture. If your light fixture requires 220V, you should use a dimmer pack rated for 220V.
The time taken for an electrician to install a light fixture can vary depending on the complexity of the installation. On average, it may take anywhere from 30 minutes to 2 hours for a standard light fixture installation.
Yes. For more information open discussion question page with more details as to what you want to do.
To convert a swivel recessed light to accept a pendant light kit, you will need to remove the existing recessed light fixture and install a pendant light fixture in its place. This typically involves disconnecting the wiring for the recessed light and attaching it to the pendant light fixture according to the manufacturer's instructions. You may also need to install a mounting bracket to support the pendant light fixture.
No, the fixtures do not have anything is common other that emitting light. If you are talking about removing the fluorescent fixture and installing a new fixture that can take a LED lamp then the answer is yes.
Yes. The Home Depot has a kit for about $10 that converts a recessed can to accept a standard fixture. Weight limit is about 10 pounds.
No, a dimmer pack will not convert the voltage. It simply controls the amount of power (voltage) sent to the light fixture, allowing you to adjust the brightness. You need to ensure that the dimmer pack is compatible with the voltage of the light fixture. If your light fixture requires 220V, you should use a dimmer pack rated for 220V.
30 inches
The time taken for an electrician to install a light fixture can vary depending on the complexity of the installation. On average, it may take anywhere from 30 minutes to 2 hours for a standard light fixture installation.
Standard rule, top to the fixture same height as top to the door.
Yes. For more information open discussion question page with more details as to what you want to do.
A fancy light fixture may be called a chandelier(originally a hanging candelabra).
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
Take the nut off at the bottom of the light fixture by unscrewing it.
The general price for a moern light fixture, depending on the amount of voltage and length/size, will generally run t about $20 for a standard room light.