Wiki User
∙ 12y agoFor USA, Canada and countries running a 60 Hz power supply service.
In order for 240 to be split, there has to be a 'neutral' involved, so that the 240 has a common reference around the splitting point. Electrically, it would look like, 120-0-120 with the neutral wire in the center.
Usually a 240 volt incoming line can be split at the main panel with the proper breakers, etc. to form a new 120 volt circuit. This is the only safe way to do it because you need the protection of a proper-sized breaker for the new 120 Volt circuit.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 12y agoTo split a 240 volt outlet into two 120 volt outlets, you will need to install a new electrical circuit with a double-pole circuit breaker. Each outlet will then be connected to one of the hot wires from the circuit breaker, while sharing the neutral and ground wires. It is important to consult a licensed electrician to ensure the work is done safely and up to code.
Wiki User
∙ 9y agoOne wire would have to be changed to a neutral wire. It would be put on the neutral bar in the electrical panel.
No, a GFCI outlet is designed for use with standard 120-volt circuits. Attempting to use a GFCI outlet with a 240-volt split circuit could cause damage to the outlet, the circuit, and could present a safety hazard. It is not recommended to use a GFCI outlet in this manner.
No, you cannot simply cap one leg of a 240-volt circuit and change the breaker to convert it into a 120-volt outlet. This requires rewiring the circuit to provide 120 volts, including changing the outlet and possibly other components to be compatible with the lower voltage. It's recommended to consult with a licensed electrician to properly convert the outlet.
No, you cannot simply change the wall plug to make a 110 volt outlet support a 240 volt appliance. The voltage requirements of the appliance and the outlet must match for safe operation. You would need to install a dedicated 240 volt outlet and ensure that the wiring and circuitry can handle the higher voltage. It is recommended to consult a licensed electrician for this type of electrical work.
A 120 volt duplex outlet is the main type of outlet for residential outlet system. The wires are typically white and black, and there should only be two of them.
No, the Norelco 905RX is designed for 110-120 volt outlets and should not be plugged into a 220 volt outlet as it may damage the device. It's recommended to use a voltage converter or transformer that is suitable for your particular device in order to safely use it with a 220 volt outlet.
A 15 amp 125 volt outlet is a household outlet.
No, you cannot simply cap one leg of a 240-volt circuit and change the breaker to convert it into a 120-volt outlet. This requires rewiring the circuit to provide 120 volts, including changing the outlet and possibly other components to be compatible with the lower voltage. It's recommended to consult with a licensed electrician to properly convert the outlet.
Yes.
The outlet may have a higher voltage reading due to an issue with the wiring, a problem with the outlet itself, or a problem with the electrical panel. It's important to have a qualified electrician investigate and address this issue to ensure the safety of your electrical system.
no
zzzzzzzzzzzAAAAAAAAAAAAAAAPPPPPPPPPP !!!!!
No a 208 volt outlet does not need a neutral. 208 volts is the line voltage between any two legs of a three phase 208 volt system.
A 120 volt duplex outlet is the main type of outlet for residential outlet system. The wires are typically white and black, and there should only be two of them.
yes
Yes
No, it will cause the bulb to blow. A 12 volt light is DC voltage and your home outlet is AC voltage.
If you have 240V across the hot and neutral wires in a 120V outlet, it suggests there is a wiring issue with the outlet, possibly due to a short circuit. This is dangerous and can lead to electrical shocks or fires. It is best to immediately turn off power to the outlet and seek professional help to resolve the issue.