0
A switched duplex receptacle can be wired two ways. If both duplexes are to be switched then the receptacle is wired the same as any light fixture. The black wire from the bottom of the existing switch goes to the brass screw on the receptacle that is to be switched. The white wire terminates on the neutral silver coloured screw. If you want just half of the duplex receptacle to be switched then the tie bar between the two brass screws on the receptacle has to be removed. Just wiggle it until it breaks free. Usually on a half switched receptacle the top half is switched and the bottom half remains a normal connection. After removing the tie bar, the top half of the receptacle is wired the same, as the description above, for a full duplex switched receptacle. Questions use the discuss question page.
To wire two electrical receptacles in one box, you will need to run a cable from the main power source to the first receptacle, then another cable from the first receptacle to the second receptacle. Connect the black wires to the brass screws, white wires to the silver screws, and ground wires to the green screws on each receptacle. Make sure to use wire nuts to secure the connections and follow all local electrical codes.
Black is Hot and White is Neutral and there should also be a bare ground wire. One black/white/bare cable is supply for receptacle and the other is connected in parallel and goes to another outlet.
You need your ceiling fixture connected to one of the wires coming into the receptacle box, Black to Black, White to White and Bare to Bare. However, assume you want to be able to switch the ceiling light with a wall switch unless there is to be a pull chain on ceiling light.
To connect switch run a new wired from the receptacle to a switch and run a wire from switch to ceiling fixture. At original outlet connect as described above. At switch connect White wires together with a wirenut, then do the same for the bare wires. Connect Black wire going to ceiling to one side or switch and Black wire coming from original receptacle to other side of switch.
The supply black (Hot) wire from the outlet feeds each switch (attach two pigtail black wires from the outlet black wire). The other side of each switch goes to the load. The three white wires (Neutral) get connected together (1 from outlet and 1 from each load). The three bare wires (ground) also are connected together.
To install two electrical outlets on one circuit they have to be paralleled with each other and parallel to the incoming feeder. The "hot" black wire picking up the brass coloured screws of the receptacle and the neutral white wire picking up the silver coloured screws of the receptacle.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized
IF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Add your answer:
Earn +20 pts
How do you fix a light switch after two live wires touch?
There has to be more to this question for a good answer. For the most part a light switch has two contacts, with a wire at each one. One live wire and another going to the light itself. There is also a neutral wire return (from the light to the electrical panel). There is only one live wire in any electrical circuit. [Please, don't flame me with examples of multiple electrical sources in circuitry. We're talking about home lighting.] If somehow you shorted the live wire from the switch to the electrical box (ground) or to another wire in the box, it was only momentary and you can just proceed with replacing the switch. It's a good idea to turn off the power first.
I am trying to put up a light fixture but it has three wires a white one a black one and a Coppertone where does the coopertoned wire go?
The copper wire is the ground wire and should be connected to the ground screw on the light fixture mounting bracket or to the ground wire in the ceiling box if present. Make sure to turn off the power at the breaker before working on the wiring.
Electrical wire sheathing should not project more than about one inch into the?
Electrical box to ensure proper installation and prevent short circuits. This excess sheathing can create a fire hazard, so it should be trimmed back to avoid any issues. It is recommended to leave about 1/4 inch of sheathing inside the electrical box for safety and proper wire connection.
How to extend a wire if an existing wire is short in the junction box?
You can splice additional wire onto the existing wire using wire connectors. Make sure to match the wire gauge and use proper insulation for safety. Cut the new wire to the desired length, strip the insulation, then twist together and secure with a wire connector. Finally, insulate the connection with electrical tape or heat shrink tubing.
How do you add another porch light to an existing switch?
To add another porch light to an existing switch, you can run a new electrical wire from the existing light fixture to the new porch light location. Connect the new wire to the new light fixture, ensuring all connections are secure and following proper electrical wiring guidelines. Test the new porch light to ensure it operates correctly from the existing switch.
How do you fix a light switch after two live wires touch?
There has to be more to this question for a good answer. For the most part a light switch has two contacts, with a wire at each one. One live wire and another going to the light itself. There is also a neutral wire return (from the light to the electrical panel). There is only one live wire in any electrical circuit. [Please, don't flame me with examples of multiple electrical sources in circuitry. We're talking about home lighting.] If somehow you shorted the live wire from the switch to the electrical box (ground) or to another wire in the box, it was only momentary and you can just proceed with replacing the switch. It's a good idea to turn off the power first.
I am trying to put up a light fixture but it has three wires a white one a black one and a Coppertone where does the coopertoned wire go?
The copper wire is the ground wire and should be connected to the ground screw on the light fixture mounting bracket or to the ground wire in the ceiling box if present. Make sure to turn off the power at the breaker before working on the wiring.
Into what should electric wire sheathing not project more than one inch?
Electrical wire sheathing should not project by more than one inch into where the wire terminates into a specific device. An example is a junction box or branch circuits terminating into a distribution panel.
How does one install pendant lighting?
The most important step is to make sure that the electricity is turned off to the project being worked on. Put a mounting bracket over the electrical box and tighten the screws. Twist the grounding wire to the grounding screw. Put the pendant together as per the instructions provided. Hold the canopy section near the electrical box. Using wire nuts, connect the wires from the canopy to the electrical box, keeping like colors together. Put the wire connectors in the electrical box. Using the hardware that the light came with, affix the canopy to the bracket. Turn the power back on and test to make sure it works.
Electrical wire sheathing should not project more than about one inch into the?
Electrical box to ensure proper installation and prevent short circuits. This excess sheathing can create a fire hazard, so it should be trimmed back to avoid any issues. It is recommended to leave about 1/4 inch of sheathing inside the electrical box for safety and proper wire connection.
Will a man get electrocuted if he sits on one electrical wire?
if he had bunyans
How do you complete a sentence that begins with 'Electrical wire sheathing should not'?
Electrical wire sheathing should not project more than about one inch into the electric panel.
How do 1 wire alternators work?
A one wire alternator has one wire that sends electricity to the battery and electrical system. They usually always have an internal regulator.
How do you make a bulb glow with one wire?
This is usually done by passing an electrical current through the wire.
How could you get more than one electrical circuit in the garage?
Run another wire from the electrical panel.
How to extend a wire if an existing wire is short in the junction box?
You can splice additional wire onto the existing wire using wire connectors. Make sure to match the wire gauge and use proper insulation for safety. Cut the new wire to the desired length, strip the insulation, then twist together and secure with a wire connector. Finally, insulate the connection with electrical tape or heat shrink tubing.
How do you add another porch light to an existing switch?
To add another porch light to an existing switch, you can run a new electrical wire from the existing light fixture to the new porch light location. Connect the new wire to the new light fixture, ensuring all connections are secure and following proper electrical wiring guidelines. Test the new porch light to ensure it operates correctly from the existing switch.
