Wiki User
∙ 15y agoYour house runs nowhere near 200 amps, so you need to make a list of appliances and fixtures that you use, or that you will need while the generator is running, and add their power consumption together. Add some extra capacity for growth and so the generator is not always at full power. Then talk to dealers about generators with the amount of power you need.
To run the house on a generator with the same capacity as the service that you have in your house you would need a 50 Kilowatt generator.
Wiki User
∙ 15y agoTo power a whole house with a 200 amp line, you would need a generator with a capacity of at least 15-20 kilowatts. This size generator can handle the typical power needs of a house that is connected to a 200 amp line during an outage. Be sure to consult with an electrician to ensure the generator meets your specific needs.
Wiki User
∙ 11y agoYou will need a 50 kW generator for a single phase 120/240 volt service.
I = W/E Amps = 50000/240 = 208.
If you plug a generator into your house, it can provide temporary power during an outage. The generator can power essential appliances and devices depending on its capacity, but be cautious to avoid overloading it or potentially causing damage. It's essential to follow safety guidelines and only use generators in well-ventilated areas to prevent carbon monoxide poisoning.
A 18000 watt generator at 120 volts 3 phase service would provide approximately 144 amps per phase. This is calculated by dividing the total watts (18000) by the voltage (120) and the square root of 3 for three-phase power.
An electric automatic changeover switch is a device that automatically switches power supply from one source to another in case of a power outage. It helps to ensure uninterrupted power supply by seamlessly transferring the load to an alternate power source such as a generator.
It is not recommended to run a cord from a generator directly to a 240V outlet. This can cause damage to the generator, appliances, and pose a safety hazard. It is best to use a transfer switch installed by a professional electrician to safely connect the generator to your home's electrical system during a blackout.
Hopefully the current and voltage would be zero. The generators overload and short circuit main breaker protection is there just for conditions like that. As soon as the fault is recognized by the protection the generator is taken off line.
The generator has to be synchronized to the power line before it can be connected. If connected out of phase there is a chance that the generator will motorize and this could break the crankshaft of the prime mover.
If you plug a generator into your house, it can provide temporary power during an outage. The generator can power essential appliances and devices depending on its capacity, but be cautious to avoid overloading it or potentially causing damage. It's essential to follow safety guidelines and only use generators in well-ventilated areas to prevent carbon monoxide poisoning.
I would recommend a generator or storing battery. By using solar power in the summer months and storing it for later as well as a gas generator. There isn't a good way to harness electricity outside of the main line, but using a generator to fill in the times when the power goes out would be a good idea.
Answer for USA, Canada and other countries running a 60 Hz supply service.Stop! What...? Don't try to do that...!Don't make a cable with the intention of plugging a generator into an outlet in your house, it is incredibly dangerous!Power from your generator will back-feed into the power lines, posing a severe unexpected shock hazard to any line-workers who may be fixing the lines - the very same reason you are wanting to use your generator!Plug your appliances directly into the outlets on your generator. If you want to power the outlets in your house from the generator you must do it right and install a proper 'generator transfer switch' at the main incoming breaker panel which is situated where the main electricity service cable comes into your house.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
The power factor for a three phase generator is 80 percent. The generator consumes 36 kilowatts and a line to line voltage of 400 volts.
Load rejection occurs when load is suddenly removed from the generator. The most obvious example of this is the breaker connecting the generator to the power grid opens. This results in a full load rejection. Load pick up means the generator is supplying power to a given load. When a generator comes on line, it will pick up some load that might have been supplied by another generator.
I think you mean, 'How many amperes per line does a 100-kV.A, 525-V, generator supply?' The wires that connect a generator to its load are called LINES, not phases.The equation for apparent power is: Apparent Power = 1.732 EL ILSo you simply rearrange the equation to find the line current (IL).
The speaker is 3rd in line to the presidency.
You can connect a natural gas generator for home into your existing natural gas line. Doing this saves you the hassle and time of buying gas and filling the generator. This also ensures that your generator will be running constantly and will not run out of fuel. If a member of your family requires electricity for a medical device, this will ensure they are safe and comfortable during a power outage.
In an on-line UPS the load is always being powered by the UPS and it is constantly charging so there is no switchover time. In an off line system, the system detects the lack of voltage and switches to the alternate source of power. Usually this would be a generator that would start after a short period of no supply voltage. Some critical systems would use a short duration direct system with backup generator kicking in after a short period.
I assume this is asking about the capability curve of a generator. A generator can only produce so much actual power (kW) at a specific power factor. As power factor changes, the amount of current flowing that is due to reactive power will also change. The total current Ix (reactive power) + Ir (real power) will cause heating in the generator, and so the generator can only kick out so much current, be it real power or reactive power. Reactive power is used to control the voltage (drag it down, or push it up) and change phase angles to push more power down specific lines. If the load on a generator is such that it's expected to generate power outside its' capability curve, terminal voltage may begin to sag (which will cause the generator output power to be less, potentially exacerbating the problem), or may float too high (potentially damaging equipment). Excessive heating in the generator can also result, and protective devices may kick in to trip the generator off line.
The generator, consisting inside the Hydropower plant, collects electricity from the pressure of water pushing the turbines. The long distance power line cables are attached to the generator to extract the electricity.The power lines transport all the electricity to our homes and factories