Wiki User
∙ 19y agoThat's pushing it but it can work. It depends if you have central A/C, electric range, water heater, etc. Those are your amp suckers. You'll need to be mindful when operating the hot tub; not running the dryer, oven, or other large appliances.
Wiki User
∙ 19y agoYes, adding a 60-amp GFI breaker for a hot tub to a 100-amp breaker box with other circuits could potentially overload the system. The total ampacity of all connected circuits should not exceed the rating of the main breaker. It's recommended to consult with a licensed electrician to assess your setup and ensure it can handle the additional load safely.
Wiki User
∙ 12y agoYes, but the 60A breaker will trip when your house box reaches 60A draw. I would not recommend it.
Wiki User
∙ 12y agoYes, use a 60 amp breaker to go to the 60 amp sub panel.
The circuit breaker may trip when the refrigerator is plugged in due to a power surge caused by the refrigerator's compressor turning on. This sudden spike in electrical demand can trip the breaker as a safety measure to protect the electrical system from damage. It could also be due to electrical overload if the circuit is already carrying a heavy load from other appliances.
the overload relay. This allows the overload relay to accurately measure the current being drawn by the motor and provide protection in case of an overload condition. It ensures that the overload protection is effective and responsive to the motor's operation.
If a household circuit breaker is defective, you may notice frequent tripping, electrical outlets not working, or a burning smell coming from the breaker panel. It's important to have a qualified electrician inspect and replace the defective breaker to prevent any electrical hazards.
No, it is not recommended to replace a 35 amp breaker with a 40 amp breaker for an AC unit. Breakers are designed to protect the circuit and the equipment, so using a higher rated breaker can lead to overheating and potential damage. It is best to use the correct amperage rated breaker for the equipment.
A circuit breaker switch could spark due to a buildup of heat or a high level of current flowing through it. This can lead to arcing between the contacts inside the breaker, resulting in sparking. Additionally, loose connections or damage to the breaker can also cause sparking.
Its not recommended because your new main breaker will allow up to 100 amps and your old wire can only safely handle 60amps. If you put a 60amp main breaker in the new box, that would be acceptable. No, it is perfectly safe. Because the box is overrated, there is no problem. If the box is the main panel, and not a subpanel, install a 60A main breaker so you cannot overload your service. If it is a subpanel this 60A breaker should be in the main panel.
It depends on what else you are running in the house. Add up your amperage to see if it is more than the 125amp rating. Which should be below 105 amps constant to keep from overheating the main breaker. If you are not running a big central ac system or a electric oven and water heater you should have no problem running the hot tub.
A person or thing that is going to break A person or thing that is going to break
Overload or short in system
The sump pump breaker alarm will keep going off if it is being overloading. This is usually a result of a failing pump or a clogged filter.
The circuit breaker may trip when the refrigerator is plugged in due to a power surge caused by the refrigerator's compressor turning on. This sudden spike in electrical demand can trip the breaker as a safety measure to protect the electrical system from damage. It could also be due to electrical overload if the circuit is already carrying a heavy load from other appliances.
IMO it would be because the circuit breaker has the possibility of going bad and not working (allowing a short to move through the device), but fuses blow (cause a break) no matter what if shorted.
No, it is not recommended to replace a 35 amp breaker with a 40 amp breaker for an AC unit. Breakers are designed to protect the circuit and the equipment, so using a higher rated breaker can lead to overheating and potential damage. It is best to use the correct amperage rated breaker for the equipment.
the overload relay. This allows the overload relay to accurately measure the current being drawn by the motor and provide protection in case of an overload condition. It ensures that the overload protection is effective and responsive to the motor's operation.
the amount of power going to the object will will cause the circut breaker to blow. if the object is not connected to a breaker then the object will catch on fire.
On a star delta starter a motor overload or a motor going to ground and cause a short circuit will cause the overload protection to trip. These overloads have to be reset before the motor can be restarted.
If a household circuit breaker is defective, you may notice frequent tripping, electrical outlets not working, or a burning smell coming from the breaker panel. It's important to have a qualified electrician inspect and replace the defective breaker to prevent any electrical hazards.