0
The problem with the question is the part not stated.
What is the amprage rating of the equipment and the branch wiring that was installed to provide the necessary power?
In other words, if the equipment is meant to draw 25 amps and the wire size is #10 gage, then by all means a 30 amp fuse is better, though if you are talking fuses and not breakers, then by all means install a 25 amp fuse.
However, if the wire size is #12 gage and the unit only draws 15 amps, putting a 30 amp fuse in could cause a total melt down of the system and the wiring and eventually could cause a fire. This is the reason why most insurance companies would rather see breakers installed then the removable fuses.
A moran who is tired of changing fuses because they keep blowing will rationalize that putting in a larger amprage fuse will cause them less work, but they fail to think about the safety aspect of their action. They are the ones we see on the late night news watching their homes burn to the ground and not understanding why their toaster oven went on the blink and caused this and they will, of course, have to sue this toaster oven company because it was "their" fault. A larger fuse should NEVER be installed on a system that demands a lower amprage fuse or breaker if the correct size devices are not in place.
Please trust me, there is a lot more to your question then which size fuse is better, and hopefully, for safety reasons, always lean towards the smaller size fuse unless you know better!
What else can I help you with?
What are the advantages of MCBs over traditional fuse carriers?
MCBs are more convenient to reset after tripping, as they just need to be switched back on instead of replacing a fuse. They provide better protection against short circuits and overloads due to their faster response time. MCBs also offer more precise and adjustable current ratings for different circuits.
What is the problem in using a strip of metal or any other piece of wire in place of a fuse?
The fuse is made to blow at a set amperage to protect the wire from overheating. Using anything but the fuse may cause the circuit to work but could most certainly cause the wiring to overheat and burn if it is overloaded.
Why use a dual element fuse over a single element fuse?
A dual element fuse provides better protection for equipment by being able to handle the temporary high inrush currents that can occur during normal operation. This type of fuse also has a faster response time to protect against overloads and short circuits, making it more reliable for sensitive equipment.
Why is an Residual current device better than a wire fuse?
- Using an RCD is better than a fuse because it requires no replacement sacrificial metal strip. Also, more reliable and reacts more quickly to cut the circuit (can detect quickly since it is a more sensitive device).
Can you use 250V 3.15A fuse to replace a 250V 3A fuse?
It's best if you just make a policy of never replacing a fuse with anything larger. Engineers have calculated the maximum SAFE circuit draw on an electronic device, and you should not use a fuse that will not provide adequate protection to the circuit. It sounds like .15 amp difference shouldn't cause trouble, but it's not a good idea.
A fuse has low melting point why?
This is necessary because a fuse is a protection against an overcurrent; excessive current produce melting.
What can fuses not provide protection against?
Fuses do not provide protection against ground faults. Protection against a ground fault can be provided by breakers. If a fuse blows, it has to be replaced. If a breaker is tripped to off due to a surge in electrical current, the breaker can be reset.
What is the protection of over current to a diode?
we use fuse only .thanks
Why shouldn't you put a penny under a burned-out-fuse?
The penny does not provide the over current protection that the fuse provides.
The first measure you should take to help prevent damage against electrical problems is to do what to the circuit?
Protect the circuit with an OCPD, an over current protection device, such as a circuit breaker or fuse.
What are the advantages of MCBs over traditional fuse carriers?
MCBs are more convenient to reset after tripping, as they just need to be switched back on instead of replacing a fuse. They provide better protection against short circuits and overloads due to their faster response time. MCBs also offer more precise and adjustable current ratings for different circuits.
What is meant by the term fusing factor?
Fusing factor is the ratio of a fuse's minimum fusing current (the smallest current that will cause the fuse to melt) and the nominal rated current (usually the number in Amps marked on the fuse body).
What does OPD mean in electric terms?
'Overcurrent protection devices' are used to protect conductors from excessive current flow... a fuse
Will maximum current flow through 0 ohms of resistance?
In theory, you would get infinite current. But, of course, in practise, this cannot happen, as any large current would cause severe damage to the source supplying that current, not to mention the conductors involved. Protection against such currents would be provided by a fuse or circuit breaker.
What is the problem in using a strip of metal or any other piece of wire in place of a fuse?
The fuse is made to blow at a set amperage to protect the wire from overheating. Using anything but the fuse may cause the circuit to work but could most certainly cause the wiring to overheat and burn if it is overloaded.
Why is an Residual current device better than a wire fuse?
- Using an RCD is better than a fuse because it requires no replacement sacrificial metal strip. Also, more reliable and reacts more quickly to cut the circuit (can detect quickly since it is a more sensitive device).
Why use a dual element fuse over a single element fuse?
A dual element fuse provides better protection for equipment by being able to handle the temporary high inrush currents that can occur during normal operation. This type of fuse also has a faster response time to protect against overloads and short circuits, making it more reliable for sensitive equipment.
