Wiki User
∙ 14y agoyes, as long as the wattage are almost the same which is similar to the same current
Wiki User
∙ 14y agoIt is generally not recommended to use a 120v light switch in place of a 125v switch. The voltage rating of the switch should match the voltage of the circuit to prevent potential safety hazards such as overheating or electrical arcing. It's best to use a switch that matches the voltage of the circuit.
No, the plug and device have different voltage and amperage requirements. Using a 125V 30 amp plug for a device that needs 24V 50 amp could damage the device and pose a safety hazard. It is important to match the electrical specifications of the plug and device for safe operation.
The main difference between 125V and 110VAC is the voltage level. 125V is a higher voltage compared to 110VAC. This difference may impact the power consumption, efficiency, and performance of electrical devices that operate within these voltage ranges.
No, it is not safe to plug a device rated for 125V into a 220V outlet. This could result in damage to the device or a potential safety hazard, such as a fire or electrical shock. It is important to match the voltage requirements of the device with the voltage supplied by the outlet.
A typical 125V outlet in North America has a resistance of almost zero ohms when it is connected properly. The outlet is designed to provide a pathway for electricity to flow easily without significant resistance. The resistance can increase if there are issues with the wiring or connections.
No, you cannot plug a device rated for 125V into a 220V outlet directly. Doing so may damage the device and pose a safety hazard. You would need a voltage converter or transformer to safely use the device with the higher voltage.
See discussion page for more.
Yes ,it's the same voltage.You have a +-5% of voltage range
No, it is against the National Electrical Code to wire a receptacle with the wrong voltage. You should call a qualified electrician to change the 250V receptacle to a 125V receptacle.
minimum 230volts In formal electrical jargon, a "device" does not "use" electricity. A device is something like a switch or receptacle(outlet) that helps control or carry electricity but does not consume electricity. In the United States, voltage for home lighting and general purpose receptacles is 120v. Voltage for electrical appliances such as ranges, clothes dryers, or furnaces is 240v. Voltages such as 110v, 115v, or 125v are versions of 120v in electrical jargon and voltages such as 220v or 230v are versions of 240v.
no.. it could damage your electrical components.
Yes. Use 10awg wire, mindfull of length voltage drop.
The voltage rating of a fuse (in this case 125V or 230V) defines the maximum circuit voltage that the fuse is safe to be used on. A fuse with a voltage rating of 125V should not be used in a circuit with a voltage greater than 125V. If a 125V fuse were installed in a 230V circuit and an overload current occurred, the fuse could explode.
No, the plug and device have different voltage and amperage requirements. Using a 125V 30 amp plug for a device that needs 24V 50 amp could damage the device and pose a safety hazard. It is important to match the electrical specifications of the plug and device for safe operation.
The main difference between 125V and 110VAC is the voltage level. 125V is a higher voltage compared to 110VAC. This difference may impact the power consumption, efficiency, and performance of electrical devices that operate within these voltage ranges.
Yes and no. The voltage rating of the cord and appliance are compatible, so that's not an issue. However, the cord must be thick enough to handle the maximum load the appliance will draw (amperage). Thicker cords (lower wire gauge) can handle more current. Running high draw 120V appliances, such as toasters, microwaves, window AC units and especially hair dryers on extension cords or undersized wiring is a serious fire and shock risk. Special heavy duty appliance cords (usually 10 gauge wire and <10' long) are available for 120V applications at most hardware stores. Ideally, the cord would be hard wired into the appliance, and not be excessive in length. The ground pathway, if applicable, should be maintained as well.
No it will not work.
no