0
A 60 horsepower motor typically requires a minimum breaker size of 100 Amps for normal operation. It is important to consult the motor's specifications or a licensed electrician to ensure the correct breaker size for safe and efficient operation.
Add your answer:
Earn +20 pts
What is the minimum size breaker panel for a home?
In North America the smallest size breaker found in a home distribution panel is rated at 15 amps
What size wire and breaker for a 7.5 hp motor?
For a 7.5 hp motor operating at 240V, you would typically use a 14-gauge wire and a 40 amp breaker. However, it is best to consult the motor's specifications and the National Electrical Code to determine the exact wire size and breaker needed for your specific setup.
What is the breaker size for a goulds century pump 1081?
The breaker size for a Goulds Century pump 1081 would depend on the specific model and voltage requirements. Refer to the owner's manual or the nameplate on the pump motor for the correct breaker size recommended by the manufacturer. It is important to match the breaker size with the electrical requirements to ensure safe operation.
What is breaker size for 240 volt 9 KW?
The formula you are looking for is I = W/E.
What size breaker do you need for a well pump?
A breaker is based on the amperage that is drawn by the pump motor load. Find the full load amperage of the motor. The wire fed from the breaker has to be rated at 125% of the motors full load amperage. The breaker for motors have to be over sized, usually 250% of the motors full load amps.
What size of breaker is use for 75 horsepower 220 volts 3 phase induction motor?
500 amp breaker with 250 mcm cu conductors, NEC list this motor as drawing 192 amps X 250% = 480amps go to the next standard size of breaker which would be a 500.
What size breaker is used for a 300 horsepower motor?
A breaker is based on the amount of current that the motor draws. This amperage should be taken off of the motors nameplate. In motors of a specific horsepower the amperage is proportional to the voltage the motor uses. Without the motors voltage this question can not be answered.
What size breaker is needed for a 125 hp motor?
It depends on what the amperage of the motor is. The motors amperage depends on the voltage of the motor. The higher the voltage the motor operates on the lower the amperage. So unless the amperage from the motor's nameplate is stated an answer can not be given.Just remember that the feeder capacity to the motor has to be 125% of the motors full load amperage and the breaker protecting the conductors to the motor has to be rated at 250% of the motors FLA. This higher breaker size allows the motor to start without tripping a normal size breaker that is rated for the lower conductor size.
LRA is 134 AMPS. what size breaker should be used?
LRA (locked rotor amps) is not used to calculate the breaker size. Breaker's are used to protect the size of the conductor that is connected to it. Motor calculations are based on the motor's FLA (full load amps).Conductor size is 125% of the motor's FLA.Breaker size is 250% of the motor's FLA.This is the only occasion when the breaker is sized larger that the conductors maximum amperage rating. This is due to the motor drawing up to 300 to 600% of its FLA when starting.If you state the motor's wattage, voltage or amperage this calculation can be calculated here.
What is the minimum size breaker panel for a home?
In North America the smallest size breaker found in a home distribution panel is rated at 15 amps
What is the minimum size breaker panel for a home's main service?
50 amps
What size breaker is needed for feeding 10 kva transformer at 460 v single phase?
One horsepower (electric motor) is 746 watts, so ten horsepower is 7460 watts. Divide that by a power factor (assumed) of 0.8 and you get 9325 volt-amps. Divide that by a voltage (again, assumed) of 240 and you get 39 amperes. For calculation purposes the electrical code book states that a 10 horsepower motor at 240 volts will draw 50 amps. The motor's nameplate amperage that is driving the rotary phase converter should all ways be used first. The electrical code requires a breaker for a motor to be 250% of the motor's operating full load current. 250% of 39 amperes is 97 amperes. I would use a 100 ampere breaker for a 10 horsepower motor. If the motor rating is used from the code book values, then 50 x 250% would equal 125 amps and that is the size of the breaker that must be used. This is the reason that the motor's exact name plate amperage rating should be used. In the long run feeder wire costs could make a saving in the overall projected costs.
What is the minimum size breaker panel required for a homes main service?
50 amps
What size breaker should be used on a 20 amp motor?
30 amp breaker with #10 gauge copper wire
What size wire and breaker for a 7.5 hp motor?
For a 7.5 hp motor operating at 240V, you would typically use a 14-gauge wire and a 40 amp breaker. However, it is best to consult the motor's specifications and the National Electrical Code to determine the exact wire size and breaker needed for your specific setup.
Which is faster Lamborgini or Ferrari?
It depends, it has to do with the weight, horsepower, and size of motor. The heavier the car is the slower. The less horsepower the car is slower. and if the motor is small the slower it goes.
Is it legal under NEC to extend a 480 volt 3 phase 20 amp circuit with different size conductors for L1 L2 and L3 as long as the gauge meets the circuits ampacity requirements?
I assume your sizing the 20 amp from the breaker? NEC 240.3 states minimum conductor size for the rated ampacity of the circuit breaker. In this case, minimum size for 20 amp breaker is 12 AWG. I assume you are wiring a motor? I suggest you size your over current in accordance with NEC, start reading around NEC 430.
