0
Originally a 240V line running from the 50A circuit to a box contaning in line fuses from this box came a 240V cable having 2 black wires and wire braid do I wire the outlet stove as a 3 or 4 prong?
Wiki User
∙ 17y ago
3 prong the 2 black wires are your hot and the braided is your neutral.
Wiki User
∙ 17y ago
Based on the description, it sounds like you should wire the stove outlet as a 3-prong outlet since the cable you have appears to have two hot wires and a ground wire (wire braid). Connect the two black wires to the hot terminals and the wire braid to the ground terminal on the stove outlet. Remember to ensure that the circuit is properly grounded for safety.
Add your answer:
Earn +20 pts
What does a draw out circuit breaker mean?
A draw-out circuit breaker is a type of circuit breaker that can be easily removed from its housing for maintenance or replacement without having to shut down the entire system. This feature allows for quick and convenient access to the circuit breaker for servicing purposes.
How can you prevent having a overloaded circuit?
Option 1: Use a circuit breaker. The breaker is essentially a switch that will turn off the electricity in the event of a current overload fault occurring somewhere either in appliances connected to the circuit or to the circuit's own wiring. Option 2: Use a fuse. Will turn off the electricity in the event of a current overload. One downside is that fuses destroy themselves in order to cut-off the power, so you have to replace them. Another downside is that some of the simpler types of fuse are not as fast-acting as a circuit breaker so they can allow more damage to occur before they shut off the supply of current.In reality, unlike a circuit breaker, a fuse is not really an "overload protection device" but a "device for opening a circuit which has a higher current subjected to it than it was designed to carry", such as a short circuit condition.For example certain types of electric motor need to draw a high start-up current so a circuit feeding such a motor must be fused at up to 250% of the motor's rated running current or Full Load Amperage (FLA). So a motor could be in an overload state up to 200% over its FLA and still not blow the fuse. For more information about circuit protection devices see the answers to the Related Questions shown below.
what is the action of the upper body when running?
New research stresses the importance of having a strong upper body when it comes to running efficiency. Training your upper body improves your running because it helps you prevent fatigue and improves endurance.
Which safety tip should you use if you have a overload circuit?
If you have an overloaded circuit, the safest tip is to immediately turn off the power at the circuit breaker panel to prevent overheating or electrical fires. Identify the source of the overload by unplugging some devices and redistributing them to other circuits. Consider having an electrician inspect and upgrade your electrical system if overloads are a recurring issue.
How many lighting outlets are permitted on a branch circuit?
The National Electrical Code typically allows a maximum of 12 lighting outlets on a 15-amp branch circuit and 16 lighting outlets on a 20-amp branch circuit. However, these numbers can vary based on local code requirements, so it's important to check with your local authority having jurisdiction.
How does closed circuit work?
A closed circuit works by having electricity flow in a complete circuit or circle or any closed shape.
What does parallel circuit mean in science?
A circuit having two or more paths connected across the source.
What are the classes of failures in a tranformer?
Biggest problems are the windings either having an open circuit or a short circuit.
What is the current running through resistor 1?
I'm having some trouble focusing in on the schematic of the circuit.
Is there alternatives to measure the electrical resistance of powder without having to compress them?
I am not 100% sure, but if you add the powder into a aqueous solution contaning electrolytes and compared the conductivity before and after you added the powder into the aqueous solution, it may display a difference in conductivity.
What are hazards of having too many amps on a circuit?
it may explode
Do parallel circuits share a circuit?
No they dont sice they are having more the
How can you prevent having an overloaded circuit?
The thing that prevents an overload is the fuse.
How do you know an electrical circuit has a short in it?
A short circuit is determined by a low resistance between two conductors or between a conductor and the ground. <<>> The circuit's over current protection usually trips resulting in the circuit having no power.
How you can minimize the loading effect on voltmeter?
To minimize the loading effect on a voltmeter, use a voltmeter with a high input impedance. This will ensure that the voltmeter draws as little current as possible from the circuit being measured, reducing the impact on the voltage being measured. Additionally, connecting the voltmeter in parallel with the circuit, rather than in series, can also help minimize the loading effect.
What is the advantage of having a parallel circuit as oppose to a series circuit?
depends on the load. if it is lights one can burn out without turning off the others
Does a fire alarm circuit have to be in a separate conduit?
yes because of it having a signals, if it mix with power cable, fire alarm circuit get distributed.
