The colors only matter if you are trying to pair up to an already headed end. Whats more important is the pins you use. For cat5e and normal 10/100 ethernet you only use pins 1,2,3,and 6. Cat5e has 4 paired wires (orange-white / orange/ blue-white / blue / green-white / green / brown-white / brown) A typical standard head is colored this way, starting from pin 1-8: 1) orange-white 2) orange 3) green-white 4) blue 5) blue-white 6) green 7) brown-white 8) brown So, its possible to use the orange pair, and green pair for one outlet, then re-wire the blue pair and brown pair to the second outlet as long as its headed to use pins 1,2,3,6 on both ends.
The longest Xbox 360 Ethernet cable you can use is typically 100 feet (30 meters). Using a cable longer than this can result in a loss of signal quality and slower connection speeds. It's best to keep the cable length as short as possible for optimal performance.
Generally speaking, UTP of Cat5, Cat5e, or Cat 6 is physically terminated with either an RJ-45 plug or RJ-45 jack. The wiring pattern depends on whether you are using 568A or 568B as your cable standard.
RJ45 is a sort of connector generally utilized for Ethernet organizing. It seems to be like a phone jack, yet is marginally more extensive. Since Ethernet links have a RJ45 connector on every end, Ethernet links are some of the time additionally called RJ45 links. The "RJ" in RJ45 remains for "enlisted jack," since it is an institutionalized systems administration interface. The "45" essentially alludes to the quantity of the interface standard. Each RJ45 connector has eight pins, which implies a RJ45 link contains eight different wires. On the off chance that you take a gander toward the end of an Ethernet link, you can really see the eight wires, which are every an alternate shading. Four of them are strong hues, while the other four are striped.
The wiring that connects workstations to the closest telecommunications closet is typically done using structured cabling, such as Ethernet cabling (Cat5e, Cat6, etc.). These cables are run from each workstation to the patch panel in the telecommunications closet, where they are connected to the network switch. This setup allows for a centralized and organized network connection for each workstation within the building.
yes
yes ;)
Category 5 or 6 cable.
Cat5e is 100 mbps.
One may use Cat5e network cable in bulk to connect to the internet or ethernet. Large amounts of cable may be used in a business or office setting to improve signals and connections.
One can purchase a cat5e patch cable at a local department store such as Walmart, Target, AAFES, and the NEX. One could also purchase online at sites such as Amazon.
another name for an ethernet cable is a cat5 or cat5e cable
100 feet Cat5e cables can be purchased through many different locations. Some common places to look are Firefold, Cable Wholesale and Cable and Kits through the internet.
12mm to 1/2 inch
Cat6 cable is very similar to Cat5e cable. It is, simply put, just held to a stricter standard than Cat5e cable. Since Cat6 is made to a higher standard than Cat5e it will support higher speed transfers. Cat5e cable can be used for networks up to a 1Gbps speed while Cat6 is currently rated for up to 10Gbps speed. Cat7 takes this even further and supports 40Gbps. For normal usage on networks up to 1Gbps and no run being longer than 100 meters, Cat5e is completely sufficient for the network. To ensure forwards compatibility it may be worthwhile to install Cat6 cable while you're at it so you don't hit a speed cap in your network down the road.
To wire a Cat5e jack correctly, follow these steps: Strip the outer insulation of the Cat5e cable to expose the inner wires. Untwist the pairs of wires and arrange them according to the T568A or T568B wiring standard. Insert the wires into the appropriate slots on the Cat5e jack. Use a punch-down tool to secure the wires in place. Test the connection using a cable tester to ensure proper connectivity.
a punch down tool