0
What else can I help you with?
What is the remote switch wire for an ATX or BTX power switch connected to?
The remote switch wire for an ATX or BTX power switch is typically connected to the motherboard's front panel header. This header is where you connect various front panel connectors, including the power switch, reset switch, power LED, and HDD LED. The specific pins differ depending on the motherboard model, so it's important to consult the motherboard manual for the correct connection.
Power supply with red led light?
If you are referring to a switched UK-style socket outlet fitted with a led, or a wall switch fitted with a led, then the led merely indicates that the socket outlet switch or wall switch is in the 'on' position.
What happens if you move a switch and the circuit wires are not all connected?
When a switch is open (wires not connected) it is considered off. When a switch is closed it is considered on. If you move a switch and the wires are not connected the the circuit is open and current cannot run throughout the circuit to power the device.
When using the remote for a Hunter fan-light the light will not turn on-off using the remote-it will turn on-off using the wall switch but the fan will turn on-off using the remote Any ideas?
The fan is wired to the house wrong. Typically the red switch wire in the ceiling box will be nutted off and not used when a remote is installed. Sounds like, in this case, the fan light wire (blue) was connected to the red switch wire in the ceiling box instead of being correctly connected to the remote unit at the fan.
Which is the load side on a double pole switch?
The load side of a double pole switch is the side where the outgoing electrical current flows to the connected device, such as a light fixture or appliance. It is typically opposite to the line side, which is where the incoming electrical supply is connected.
How do you make a remote controlled switch board?
I would use relays, connected to the original wires, also connected to your wireless setup
All three legs of my dimmer are hot?
If the hot is connected to the supply and it is turned on and the switch is turned on and the neutral not connected this could be quite true. Connect the neutral to the supply neutral and shut the switch off. Now the only reading that you should get is the hot supply.
How does a remote control operate a switch from a distance?
The remote control sends a radio signal to the base unit, and the base unit interprets the signal to switch the connected appliance on or off. Some remote control can operate multiple switches from a distance.
What is the remote switch wire for an ATX or BTX power switch connected to?
The remote switch wire for an ATX or BTX power switch is typically connected to the motherboard's front panel header. This header is where you connect various front panel connectors, including the power switch, reset switch, power LED, and HDD LED. The specific pins differ depending on the motherboard model, so it's important to consult the motherboard manual for the correct connection.
How do i wire a toggle switch for an amp?
Hook a switch up to the remote turn on and ground. Before the wiring for the amp.
Advantage of multiple control remote switch?
If you have two switches connected to a light in a room.example your bed room and you are in your bed you wont have to get out of your bed to switch off the light but u can switch it off by pulling a switch over your head.
Why switch is always connected in the phase?
Switches are used to isolate the supply voltage from the connected load. This isolation is needed to be able to work on equipment in the de-energized state. Without the switch in the circuit this could not be accomplished.
How do you replace gas fireplace switch?
This depends on the switch. A lot of older fireplaces have a millivolt valve with a toggle-switch sticking out. We usually remove the toggle switch and run the 2 wires that were connected to the toggle to a remote receiver box. This way any simple remote transmitter will act like an electrical toggle switch. Most receivers will recognize hundreds of thousands of signals so this is usually very convenient and takes about 3 minutes to turn a manual switch into a remote switch.
On which line is the switch of electrical appliance connected?
A Switch on a domestic supply has always got to be on the LIVE part of that circuit. A double pole switch switches both the LIVE and NEUTRAL off together.
What is a remote light switch?
A remote light switch is a switch that triggers a light by remote. You can get one installed through your local home department store and have it rigged up to a universal remote.
Why cant one pc use the resources on the other pc connected to a switch?
You haven't invoked the right permissions or enabled remote accesses
Installed bulldog remote start Why won't 99 suburban start?
First and most obvious, are all of the connections made correctly? The one thing that will mess up a remote starter is a bad neutral safety switch, it will always check to be sure that is set to park or neutral before allowing the start sequence, so check your neutral/park switch and be sure it is functional and connected.
