If nothing goes wrong with the wiring system, then nothing 'happens'.
The ground (protective) conductor is a safety feature for when things do go wrong. In the event of a breakdown in insulation, allowing a line (live) conductor to make contact with exposed metalwork (e.g. the frame of a washing machine or other appliance), the ground conductor will allow a fault current to flow back to the supply which is large enough to operate the circuit's over current protection device (fuse or circuit breaker) to operate, disconnecting the circuit.
If you don't connect a ground wire to a light fixture, the fixture may not function properly or could pose a safety hazard. The ground wire is crucial for redirecting electrical surges away from the fixture and preventing electric shock. It is important to always follow proper wiring practices to ensure the safety and functionality of your electrical system.
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
Yes, you can connect a wall switch to an existing light fixture by running a new electrical wire from the switch to the fixture. This allows you to control the light fixture independently of the existing fixture. It is recommended to consult a licensed electrician to ensure proper wiring and installation for safety.
To string 2 light fixtures together, you will need to connect the wires of the first fixture to the wires of the second fixture using wire nuts. Make sure to connect the corresponding wires (e.g., black to black, white to white, and ground to ground). If the fixtures have separate power sources, you may need to run a new wire from the power source to the second fixture. It is always best to consult a licensed electrician if you are unsure about wiring electrical fixtures.
The red and green wires are likely the live and ground wires, respectively. To connect them to a ceiling light, connect the green wire to the ground screw on the light fixture and connect the red wire to the live wire on the fixture. Make sure to turn off the power before working on the wiring to avoid any accidents.
To connect multiple lights to one switch starting at the light, you will need to run a cable from the first light fixture to the switch. Connect the hot wire to the switch, along with a pigtail wire to connect to each light. Then connect each light fixture to the pigtail wire to create a parallel circuit. Make sure to follow proper safety precautions and consult a professional if needed.
Yes. Connect Black to Black, White to White and bare ground wires together.
Connect the ground wire to the metal box.
If you mean 2 bare copper wires those are the ground wires. Tie them together and then connect the light fixture ground wire which will be green or bare copper to those ground wires.
I always connect the ground wire to the box. However, if there is no real ground wire running back to the panel it really does you no good. The NEC requires that you rewire the circuit with the proper conductors. Remember that the ground is for your protection. Without a proper ground, you run the risk of injury or death if the fixture wiring fails.
If you are referring to a porcelain or plastic ceiling light fixture most do not have a place to connect the ground wire. You cannot ground these type fixtures. Just connect the ground wire to the mounting crossbar and forget about connecting it to the light itself. It is on the ceiling and will never be touched unless you change the bulb and then you will have the switch in the off position. It is perfectly safe.
it will explode
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
Yes, you can connect a wall switch to an existing light fixture by running a new electrical wire from the switch to the fixture. This allows you to control the light fixture independently of the existing fixture. It is recommended to consult a licensed electrician to ensure proper wiring and installation for safety.
To string 2 light fixtures together, you will need to connect the wires of the first fixture to the wires of the second fixture using wire nuts. Make sure to connect the corresponding wires (e.g., black to black, white to white, and ground to ground). If the fixtures have separate power sources, you may need to run a new wire from the power source to the second fixture. It is always best to consult a licensed electrician if you are unsure about wiring electrical fixtures.
To control a light with a switch, the switch has to be connected in series with the light fixture.
The red and green wires are likely the live and ground wires, respectively. To connect them to a ceiling light, connect the green wire to the ground screw on the light fixture and connect the red wire to the live wire on the fixture. Make sure to turn off the power before working on the wiring to avoid any accidents.
To connect multiple lights to one switch starting at the light, you will need to run a cable from the first light fixture to the switch. Connect the hot wire to the switch, along with a pigtail wire to connect to each light. Then connect each light fixture to the pigtail wire to create a parallel circuit. Make sure to follow proper safety precautions and consult a professional if needed.