0
Ground and neutral are kept separate for a reason. They are only "bonded" at the main panel. The reason is that you can create what are called ground loops where current can flow. This is because all wires have some resistance and by connecting neutral and ground you open yourself to these ground loops which can cause shocks or can adversely affect electronic equipment.
What else can I help you with?
What do you do when the ground wire from the wall is too short to reach the grounding screw on the new fixture plate?
Splice a new green wire to extend it, using the same size gauge of wire. Do not use wire nuts, use a proper electrical connector with grub-screws which can be securely tightened-up. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Do you put electrical tape around a spliced ground wire?
No, it is not recommended to put electrical tape around a spliced ground wire. The ground wire should be securely connected using a wire nut or another appropriate connector as specified in electrical codes to ensure a reliable connection and safety.
How do you wire 2 new lights with on-off switches using wires coming from an existing outlet?
You can attach/splice into the power feed to outlet (ways of doing this can vary with how the outlet is wired but make sure that all or part of the outlet isn't controlled by an existing switch). You can then take the hot, neutral and ground to a light fixture or to the first switch, then to the second switch. It is normally easier to do this project by taking power to the light (s) first, with 2 wire drops to the switches, from basement or attic.
If you ground wire is not long enough can you connect 2 wires together and then ground it to the grounding post?
* Yes. Extending the ground wire will have no adverse effect and will properly ground the device. * It is important that the splice be accomplished properly. That means that the extension conductor [wire] be of adequate size to carry the load, the surface of both conductors at the splice be clean and free of corrosion which could impede current flow, and a sound [both mechanically and electrically] splice be made.
What would be the correct wiring for 3 sets of wires into a GFCI outlet?
I'm assuming your 3 sets of wires are black or red, or some other color normally associated with the "hot" wire, a white for neutral and a green or bare conductor for ground. If your GFCI protects only itself and no other receptacles, you splice all the wires of the same color together and attach 'pig tails' to your splice to connect to the GFCI. If your GFCI protects other receptacles 'down stream', you connect only the hot and neutral feed from the panel to the line side of the receptacle. Then you splice the others together as described above and connect your pig tails to the load side. "Line" and "load" should be clearly marked on the GFCI. Your ground in this case is still all spliced together with a pigtail for connection to the GFCI. Line is from the panel. Load is to other receptacles. Getting these reversed will prohibit your GFCI from functioning properly.
Can service ground have a splice?
The main ground should not have a splice to ensure continuity of the ground. The reality is that this is done in some cases. If the splice should loosen or be intermittent you will create a shock hazard.
What are the different kinds of splice?
The five most known are the rattail joint, the western union, the fixture joint, the knotted tap and the staggered splice. Then there are crimping, wire-nutting, soldering, sty-cons.
What are the different splice of wires?
The five most known are the rattail joint, the western union, the fixture joint, the knotted tap and the staggered splice. Then there are crimping, wire-nutting, soldering, sty-cons.
Different kinds of splices and joints?
The four types of splices and joints are the Western Union splice, tap splice or tap joint, fixture splices or fixture joints, and rattail joint. The most common among the four wire splices is the Western Union splice.
What is a terminal connection used in data communication and ground circuits?
Splice
What do you do when the ground wire from the wall is too short to reach the grounding screw on the new fixture plate?
Splice a new green wire to extend it, using the same size gauge of wire. Do not use wire nuts, use a proper electrical connector with grub-screws which can be securely tightened-up. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How do you change a tail light bulb holder for a 1994 Pontiac grand am?
Cut the wires on the old fixture and splice wires from new receptacle
Do you put electrical tape around a spliced ground wire?
No, it is not recommended to put electrical tape around a spliced ground wire. The ground wire should be securely connected using a wire nut or another appropriate connector as specified in electrical codes to ensure a reliable connection and safety.
What are the different kinds of wiring splices?
The five most known are the rattail joint, the western union, the fixture joint, the knotted tap and the staggered splice. Then there are crimping, wire-nutting, soldering, sty-cons.
Where is the park neutral switch located on a 94 Cherokee 2 wheel drive and can you by-pas or jumper out?
the neutral / backup light switch is on the side of the transmission. You can cut and splice them.
Which wires do you splice to connect lights for a utility trailer on a 2005 grand caravan?
You can use "Scotch locks" on the tailights, and stop lights - trace them from the rear light fixture
How do you wire 2 new lights with on-off switches using wires coming from an existing outlet?
You can attach/splice into the power feed to outlet (ways of doing this can vary with how the outlet is wired but make sure that all or part of the outlet isn't controlled by an existing switch). You can then take the hot, neutral and ground to a light fixture or to the first switch, then to the second switch. It is normally easier to do this project by taking power to the light (s) first, with 2 wire drops to the switches, from basement or attic.
