0
dont know -------------------------------- EDIT: 2 Channel if really what its sounds like, 2 channels which means you have a Left + Right basically. 4 Channels is for 4 channels which like in a car would be Front Left + Right and Rear Left + Right. Reminder!!! Check RMS NOT max Power!!! -TheRamMan-
A 2 channel amp has two separate audio channels, typically used for powering a pair of stereo speakers. A 4 channel amp has four separate audio channels, usually used for powering multiple speakers or speaker pairs in a car audio system. The main difference is the number of channels available for connecting and powering speakers.
Add your answer:
Earn +20 pts
How many watts is a kicker impulse 352xi amp?
The Kicker Impulse 352xi amp has a maximum power output of 35 watts per channel x 2 channels at 4 ohms or 35 watts x 2 channels at 2 ohms.
How many watts is an Orion cs 100.2 amp?
The Orion CS 100.2 amp is rated for 100 watts RMS per channel at 2 ohms.
Is a 2 amp battery charger the same as a 1 amp battery charger?
No, a 2 amp battery charger has a higher charging capacity than a 1 amp battery charger. This means the 2 amp charger can charge a battery faster than the 1 amp charger. It's important to use the appropriate charger to avoid damaging the battery.
Can a mixing board effect only 1 channel on amp?
Yes it can affect only one. But the number it can affect depends on how many outputs on the mixer. Most mixers have stereo(LR,2 channel) or mono outputs. In depth:Also, there can be subgroup, auxiliary, and matrix mixes.
How do you bridge a Sony xplod 1000 watt amp?
To bridge a Sony Xplod 1000 watt amp, you will need to ensure it is capable of being bridged (most amps have a bridge mode). Then, take the positive output from one channel and connect it to the positive terminal of the speaker, and the negative output from the other channel to the negative terminal of the speaker. Finally, adjust the gain and crossover settings accordingly for optimal performance.
Can you overload a channel on a amp?
Yes you can burn a channel on an amp. Which is do to a overload. Like a 2 ohm load on an amp that is not 2 ohm stable. Will burn out a channel or both channels.
Is a 250 watt mono channel amp good enough for 2 100 watt speakers?
Monoblock amp? No. Only 1 channel which is good for one speaker, or one sub. What you need is either a 2 channel amp or a bridgeable 4 channel amp, which would be overkill anyway. If the amp you have is 2 channel, it would be ideal.
Is a 250 watt mono channel amp good enough for 2 100 watt amps?
Monoblock amp? No. Only 1 channel which is good for one speaker, or one sub. What you need is either a 2 channel amp or a bridgeable 4 channel amp, which would be overkill anyway. If the amp you have is 2 channel, it would be ideal.
What happens when you bridge an amp?
If you bridge a 2 channel 4 channel ect. you are taking the power from both channels as if it was a single channel amp.
2 door speakers do you need a 4 channel amp?
No that would be a 2 channel amp. 1 speaker per channel. 2 speakers= 2 channels 4 speakers= 4 channels
What difference between 13Ampere socket outlet and 15Ampere socket outlet?
2 Amp
What is the best amp to run 2 jl audio 10w3v3 a mono amp or a 2 channel amp?
jl audio 500/1
What is a channel in amplifier mean?
a channel refers to the speakers or subs. for example a 2 channel amp can power 2 subs or speakers. a 4 channel will power 4.
Can you use a 2 channel amp for front and rear speakers?
Use 1 channel for fronts & the other channel for the rears.
Is it bad to bridge 2 2ohm speakers on a mono or 2 channel amp?
Yup
If you have two 900 watt RMS subs what size amp do you need to properly push them?
A 2 channel 900w per channel amp or less will run it, or a 1800w one channel amp etc.. Keep in mind the ohms need to match up too
How many subs can you hook up to a mono amp?
well if its a 2 channel then 1 pair of subs like if it has only one red and one white connecters then only one pair of subs then if it has 2 of each then 2 pairs of subs that's called a 4 channel amp seacrh in Google 4 channel amp and 2 channel amp you'll see what am talking about see look http://akamaipix.crutchfield.com/ca/learningcenter/car/subwoofer_wiring/4DVC_4-ohm_4ch.jpg
