When 500 mA of current is flowing from a 4-volt supply, the supply is delivering
2 watts of electrical power. We can't tell how much of that power is actually
available from the motor in the form of mechanical power, and how much of it
is only heating up the parts of the motor.
The power of the motor can be calculated using the formula P = VI, where P is power, V is voltage, and I is current. In this case, P = 4 volts * 0.5 amps = 2 watts. Therefore, the power of the motor is 2 watts.
A 100 watt bulb typically draws around 833 milliamps (mA) of current. This calculation is done using Ohm's Law formula: Current (I) = Power (P) / Voltage (V). With a standard 120V power source, a 100W bulb would draw approximately 833mA.
It depends on the voltage of the motor, and whether it is single-phase or 3-phase. A 120 VAC 2HP single phase motor draws almost 20 amps, a 240 VAC single-phase 2HP motor draws about 10 amps. A 480 VAC 2HP three-phase motor only draws about 6 amps.
Yes 575 volts is more deadly than 220 volts. The higher the voltage becomes the higher the current becomes through a set resistance. A normal dry body's resistance from thumb to thumb is about 2.6 meg ohms. This is the body's outside resistance from point to point and not the body's internal resistance. The body's internal resistance is in the neighbourhood of 1000 ohms. Using a voltage of 220, the formula is , Amps = 220/1000 = .22 amps or 220 milliamps Using a voltage of 575, the formula is , Amps = 575/1000 = .575 amps or 575 milliamps. As you can see as the voltage goes up so does the amperage. The following list is the tolerances that the body can stand. Remember 1 amp is equal to 1000 milliamps. Less than 1/2 milliamp no sensation 1/2 to 2 milliamps Threshold of perception 2 to 10 milliamps muscular contraction 5 to 25 milliamps painful shock (may not be able to let go) Over 25 milliamps Could be violent muscular contraction 50 to 100 milliamps Ventricular fibrillation over 100 paralysis of breathing.
Yes, you can run a 220 volt 1 horsepower motor with batteries by using an inverter to convert the DC power from the batteries into AC power that the motor can use. However, the size and number of batteries needed will depend on the motor's power requirements and the duration for which you want to run it.
To make something spin in a circuit, you can use a motor. Connect the motor to a power source such as a battery and control the motor's speed and direction using a switch or a motor driver. When power is applied to the motor, it will spin and create motion.
A 100 watt bulb typically draws around 833 milliamps (mA) of current. This calculation is done using Ohm's Law formula: Current (I) = Power (P) / Voltage (V). With a standard 120V power source, a 100W bulb would draw approximately 833mA.
It depends on the voltage of the motor, and whether it is single-phase or 3-phase. A 120 VAC 2HP single phase motor draws almost 20 amps, a 240 VAC single-phase 2HP motor draws about 10 amps. A 480 VAC 2HP three-phase motor only draws about 6 amps.
Hydrostatic systems take the mechanical rotary output of an engine or electric motor and convert it to a hydraulic source of power using a hydraulic pump. The hydraulic power is converted back to mechanical power using a hydraulic motor
Have the Arduino control a relay that connects an external power source to the motor.
With increasing torque load the armature tends to slow down; the motor draws more current to compensate, and if there is armature resistance the back emf generated by the armature falls to allow the increased current to flow, which causes the motor to settle at a lower speed. The mechanical output power is the speed times the torque, and increasing the torque increases the power output provided the speed does not drop much.
No. It just draws less power.
The running refrigerator motor is using electrical energy to power the motor, which in turn drives the compressor to cool the refrigerator.
Yes 575 volts is more deadly than 220 volts. The higher the voltage becomes the higher the current becomes through a set resistance. A normal dry body's resistance from thumb to thumb is about 2.6 meg ohms. This is the body's outside resistance from point to point and not the body's internal resistance. The body's internal resistance is in the neighbourhood of 1000 ohms. Using a voltage of 220, the formula is , Amps = 220/1000 = .22 amps or 220 milliamps Using a voltage of 575, the formula is , Amps = 575/1000 = .575 amps or 575 milliamps. As you can see as the voltage goes up so does the amperage. The following list is the tolerances that the body can stand. Remember 1 amp is equal to 1000 milliamps. Less than 1/2 milliamp no sensation 1/2 to 2 milliamps Threshold of perception 2 to 10 milliamps muscular contraction 5 to 25 milliamps painful shock (may not be able to let go) Over 25 milliamps Could be violent muscular contraction 50 to 100 milliamps Ventricular fibrillation over 100 paralysis of breathing.
A motor uses electricity; it does not produce it. If you are somehow using a DC motor as a generator, then it will produce power equal to the input power minus the motor losses. If the input power is you spinning the rotor, the output power will be directly proportional to how much work you put into spinning the rotor.
Electromagnetism is an efficient way in which to turn a motor. It does not produce pollution and it is otherwise environmentally safe.
Yes, it uses power and this power must be generated by the motor using more petrol.
Yes, you can run a 220 volt 1 horsepower motor with batteries by using an inverter to convert the DC power from the batteries into AC power that the motor can use. However, the size and number of batteries needed will depend on the motor's power requirements and the duration for which you want to run it.